1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Jeffrey Slotnick
    Post

    moving backwards. need to start over.

    small update - I tried a different raspberry pi 3, but received the same results :-( I makes me really wonder about the cable, so I ordered a...
    Post by: Jeffrey Slotnick, Apr 18, 2020 in forum: Troubleshooting
  2. Jeffrey Slotnick
    Post

    moving backwards. need to start over.

    mark/omar, - thanks I'll also order a new cable.
    Post by: Jeffrey Slotnick, Apr 13, 2020 in forum: Troubleshooting
  3. Jeffrey Slotnick
    Post

    moving backwards. need to start over.

    tkoco - thanks so much for the continued suggestions. I do have a raspberry pi 3 as luck would have it - I will give it a test - might take me a...
    Post by: Jeffrey Slotnick, Apr 12, 2020 in forum: Troubleshooting
  4. Jeffrey Slotnick
    Post

    moving backwards. need to start over.

    tkoco - really appreciate the suggestions. The screen is non-responsive to touch no matter where it is now. Originally it was responsive...
    Post by: Jeffrey Slotnick, Apr 12, 2020 in forum: Troubleshooting
  5. Jeffrey Slotnick
    Post

    moving backwards. need to start over.

    Mark - if the driver isn't getting loaded then I think a new screen would have the same issue, right ? I don't mind buying another screen, but I...
    Post by: Jeffrey Slotnick, Apr 12, 2020 in forum: Troubleshooting
  6. Jeffrey Slotnick
    Post

    moving backwards. need to start over.

    tkoco / Mark. From what I can tell the image doesn't show up without the ribbon cable attached. I've tried many times to carefully attach the...
    Post by: Jeffrey Slotnick, Apr 12, 2020 in forum: Troubleshooting
  7. Jeffrey Slotnick
    Post

    moving backwards. need to start over.

    Hi tkoco, I'm now using the following image : R2-generic-image.img . Unfortunately the same results - no touch response :-(
    Post by: Jeffrey Slotnick, Apr 11, 2020 in forum: Troubleshooting
  8. Jeffrey Slotnick
    Post

    moving backwards. need to start over.

    Hi Mark - unfortunately I hadn't backed up my sd card yet before issue appeared. I ended up downloading an R2 image from here called:...
    Post by: Jeffrey Slotnick, Apr 10, 2020 in forum: Troubleshooting
  9. Jeffrey Slotnick
    Post

    moving backwards. need to start over.

    Hi Mark, Thank you so much for the idea to try. I did give that a go, but still no responsiveness on the LCD.
    Post by: Jeffrey Slotnick, Apr 9, 2020 in forum: Troubleshooting
  10. Jeffrey Slotnick
    Thread

    moving backwards. need to start over.

    Here is what happened. I had ordered a new original screen and received it. I hooked up the original screen after testing that it worked - aka...
    Thread by: Jeffrey Slotnick, Apr 9, 2020, 29 replies, in forum: Troubleshooting
  11. Jeffrey Slotnick
    Post

    Dreaded white screen of death.

    Just a quick update on this one. There are 2 main issues still. 1 - install of new screen needs to be tackled, and 2 - some sort of software...
    Post by: Jeffrey Slotnick, Apr 4, 2020 in forum: Troubleshooting
  12. Jeffrey Slotnick
    Post

    Dreaded white screen of death.

    Does that mean we have a conflict ?
    Post by: Jeffrey Slotnick, Mar 29, 2020 in forum: Troubleshooting
  13. Jeffrey Slotnick
    Post

    Dreaded white screen of death.

    hopefully I did this ok... Send: M105 Recv: ok T:16.84 /0.00 B:17.46 /0.00 @:0 B@:0 Send: M105 Recv: ok T:16.84 /0.00 B:17.66 /0.00 @:0 B@:0...
    Post by: Jeffrey Slotnick, Mar 29, 2020 in forum: Troubleshooting
  14. Jeffrey Slotnick
    Post

    Dreaded white screen of death.

    Yes - I get RoboOS - 2.0.0-r2.6 is that the wrong thing ?
    Post by: Jeffrey Slotnick, Mar 29, 2020 in forum: Troubleshooting
  15. Jeffrey Slotnick
    Post

    Dreaded white screen of death.

    Hopefully this is what you are talking about - 2.0.0-r2.6.
    Post by: Jeffrey Slotnick, Mar 29, 2020 in forum: Troubleshooting
  16. Jeffrey Slotnick
    Post

    Dreaded white screen of death.

    It seems like it is stuck at -20 for some reason. I try to set it to -6, however once I start the z offset wizard it won't progress past z ofset...
    Post by: Jeffrey Slotnick, Mar 29, 2020 in forum: Troubleshooting
  17. Jeffrey Slotnick
    Post

    Dreaded white screen of death.

    Hi tkoco, Thanks for the recommendations. I actually have already created a new SDcard with the default roboOS, this didn't improve my situation...
    Post by: Jeffrey Slotnick, Mar 29, 2020 in forum: Troubleshooting
  18. Jeffrey Slotnick
    Post

    Dreaded white screen of death.

    Wow - Ok Thanks for getting back to me Mark. 1st order of business is doing some research to try to figure out what you recommended. Thanks -...
    Post by: Jeffrey Slotnick, Mar 28, 2020 in forum: Troubleshooting
  19. Jeffrey Slotnick
    Thread

    Dreaded white screen of death.

    Hi Guys, My printer went from a great working printer to an unusable paperweight over night. I now have the dreaded white screen of death....
    Thread by: Jeffrey Slotnick, Mar 28, 2020, 20 replies, in forum: Troubleshooting
Showing results 1 to 19 of 19
Search Again