1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 1 of 6

Filters:

Prefix:
Partial Answer x
Remove All Filters:
x
Sort by:
Title Start Date
Replies Views
Last Message ↓
  1. Onion
    Locked

    Partial Answer R1plus halts mid-print, light goes off, cools off after

    Onion, Jul 23, 2025
    Replies:
    7
    Views:
    4,969
    mark tomlinson
    mark tomlinson
    Aug 8, 2025
  2. Russ_B

    Partial Answer Firmware Recommendation

    Russ_B, Sep 25, 2022
    Replies:
    2
    Views:
    1,648
    Russ_B
    Russ_B
    Sep 27, 2022
  3. joea

    Partial Answer Z_RAISE_BEFORE_HOME

    joea, Aug 19, 2021 ... 2
    Replies:
    32
    Views:
    6,091
    mark tomlinson
    mark tomlinson
    Aug 21, 2021
  4. joea

    Partial Answer Z-axis offset, adjusting.

    joea, Aug 15, 2021 ... 2
    Replies:
    31
    Views:
    6,918
    mark tomlinson
    mark tomlinson
    Aug 21, 2021
  5. Brandon Hines

    Partial Answer Bad Prints, need help!!!

    Brandon Hines, Nov 10, 2020
    Replies:
    4
    Views:
    1,560
    Brandon Hines
    Brandon Hines
    Nov 10, 2020
  6. joea

    Partial Answer My X and Y steps/mm need to be 160 not 80?

    joea, May 15, 2020
    Replies:
    1
    Views:
    1,142
    mark tomlinson
    mark tomlinson
    May 15, 2020
  7. PaulusRich1997

    Partial Answer Small Detail Print Gaps Between lines

    PaulusRich1997, Oct 21, 2019
    Replies:
    5
    Views:
    1,625
    mark tomlinson
    mark tomlinson
    Oct 22, 2019
  8. CCJ

    Partial Answer Firmware Nonresponsive

    CCJ, Sep 15, 2019
    Replies:
    1
    Views:
    1,070
    mark tomlinson
    mark tomlinson
    Sep 16, 2019
  9. Daniel Flores

    Partial Answer Filament not entering extruder

    Daniel Flores, Sep 2, 2019
    Replies:
    2
    Views:
    1,350
    mark tomlinson
    mark tomlinson
    Sep 3, 2019
  10. Dannny18

    Partial Answer Trouble with printing

    Dannny18, Sep 2, 2019
    Replies:
    1
    Views:
    1,032
    mark tomlinson
    mark tomlinson
    Sep 3, 2019
  11. robert albrecht

    Partial Answer Ughhhh I am back... MC not printing support strucures

    robert albrecht, Aug 21, 2019
    Replies:
    2
    Views:
    1,136
    BrooklynBay
    BrooklynBay
    Aug 22, 2019
  12. MarchHare

    Partial Answer New R1 (new to me) inherited from a friend. worked for him, non-functional for me. I need help

    MarchHare, Jul 31, 2019
    Replies:
    7
    Views:
    1,622
    MarchHare
    MarchHare
    Aug 1, 2019
  13. mindphunk

    Partial Answer Cooling Issue?

    mindphunk, Jul 30, 2019
    Replies:
    1
    Views:
    1,191
    mark tomlinson
    mark tomlinson
    Jul 31, 2019
  14. Connor Williams

    Partial Answer Heated bed connector replacement

    Connor Williams, Jun 13, 2019
    Replies:
    9
    Views:
    1,904
    mark tomlinson
    mark tomlinson
    Jun 19, 2019
  15. felipe fomez

    Partial Answer rods bent???

    felipe fomez, Mar 28, 2019
    Replies:
    2
    Views:
    1,258
    Geof
    Geof
    Mar 29, 2019
  16. Dan McCreary
    Locked

    Partial Answer MatterControl will not run on macOS Mojave 10.14.3

    Dan McCreary, Mar 7, 2019
    Replies:
    1
    Views:
    1,382
    WheresWaldo
    WheresWaldo
    Mar 8, 2019
  17. Kian Ghassemian

    Partial Answer My R1 is stopping after callibration

    Kian Ghassemian, Feb 27, 2019
    Replies:
    2
    Views:
    1,049
    mark tomlinson
    mark tomlinson
    Feb 28, 2019
  18. Mark Ostrander

    Partial Answer printer stops ...unable to communicate with printer

    Mark Ostrander, Feb 27, 2019
    Replies:
    1
    Views:
    971
    mark tomlinson
    mark tomlinson
    Feb 27, 2019
  19. Bd182

    Partial Answer Soft edges, higher than the center

    Bd182, Feb 19, 2019
    Replies:
    1
    Views:
    884
    Geof
    Geof
    Feb 19, 2019
  20. Domenic

    Partial Answer Layer lines on my prints are not even

    Domenic, Nov 22, 2018 ... 2
    Replies:
    36
    Views:
    7,089
    TheOneWhoWhelms
    TheOneWhoWhelms
    Feb 1, 2019
Showing threads 1 to 20 of 114

Thread Display Options

Loading...
Page 1 of 6