1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Have issues with your printer? Need some help? Post questions, and answers here!

Page 1 of 53

Filters:

Prefix:
Unresolved x
Remove All Filters:
x
Sort by:
Title Start Date
Replies Views
Last Message ↓
  1. lessthaned

    Unresolved Robo 1+ won’t print

    lessthaned, Aug 20, 2019 at 9:09 AM
    Replies:
    9
    Views:
    75
    BrooklynBay
    BrooklynBay
    Aug 21, 2019 at 7:28 AM
  2. Michael Woodward

    Unresolved After Merlin 1.1.9 upgrade, z axis will not raise in print

    Michael Woodward, Aug 20, 2019 at 5:05 PM
    Replies:
    7
    Views:
    57
    mark tomlinson
    mark tomlinson
    Aug 20, 2019 at 6:11 PM
  3. LabMinion

    Unresolved New Mega+Firmware = No motor control

    LabMinion, Jun 27, 2019 ... 2
    Replies:
    37
    Views:
    620
    mark tomlinson
    mark tomlinson
    Aug 15, 2019
  4. JWW

    Unresolved R1 Plus - Disconnecting

    JWW, Aug 8, 2019 ... 2
    Replies:
    32
    Views:
    301
    mark tomlinson
    mark tomlinson
    Aug 12, 2019
  5. robert albrecht

    Unresolved Need a little help with some lifting.

    robert albrecht, Aug 12, 2019
    Replies:
    8
    Views:
    87
    mark tomlinson
    mark tomlinson
    Aug 12, 2019
  6. Hal Reed

    Unresolved Robo R1+ Z gantry diving into print

    Hal Reed, Aug 8, 2019
    Replies:
    6
    Views:
    96
    mark tomlinson
    mark tomlinson
    Aug 8, 2019
  7. Yacobeeb

    Unresolved No power, now some power?

    Yacobeeb, Aug 6, 2019
    Replies:
    4
    Views:
    152
    mark tomlinson
    mark tomlinson
    Aug 8, 2019
  8. mdecker

    Unresolved E3D V6 hot end can't get a stable temperature

    mdecker, Jul 24, 2019
    Replies:
    6
    Views:
    134
    mark tomlinson
    mark tomlinson
    Jul 24, 2019
  9. Mike Toole

    Unresolved No power to my part cooling fan

    Mike Toole, May 18, 2019
    Replies:
    11
    Views:
    451
    mark tomlinson
    mark tomlinson
    Jul 5, 2019
  10. Lance Weston

    Unresolved Cura 4.1

    Lance Weston, Jun 13, 2019
    Replies:
    0
    Views:
    232
    Lance Weston
    Lance Weston
    Jun 13, 2019
  11. Prak Coton

    Unresolved Z Calibration changes between prints

    Prak Coton, Jun 10, 2019
    Replies:
    2
    Views:
    192
    mark tomlinson
    mark tomlinson
    Jun 10, 2019
  12. gunsmoke132

    Unresolved Z axis keeps getting out of wack during printing.

    gunsmoke132, Jun 3, 2019
    Replies:
    19
    Views:
    359
    mark tomlinson
    mark tomlinson
    Jun 8, 2019
  13. Jason F.

    Unresolved Z Homing Issue on newly updated R1+

    Jason F., Jun 4, 2019
    Replies:
    4
    Views:
    182
    Jason F.
    Jason F.
    Jun 4, 2019
  14. Springpatch Newb

    Unresolved Printing With Supports Help Request

    Springpatch Newb, May 18, 2019
    Replies:
    4
    Views:
    163
    mark tomlinson
    mark tomlinson
    May 18, 2019
  15. Barbara Yeats

    Unresolved Bed not heating - R23 light not turning on

    Barbara Yeats, May 14, 2019
    Replies:
    7
    Views:
    220
    WheresWaldo
    WheresWaldo
    May 15, 2019
  16. gunsmoke132

    Unresolved ABS bunching up in the heatbreak

    gunsmoke132, Apr 23, 2019
    Replies:
    10
    Views:
    416
    mark tomlinson
    mark tomlinson
    May 1, 2019
  17. mclemens7

    Unresolved Tried uploading an update and got an access denied. error code is below

    mclemens7, Apr 20, 2019
    Replies:
    2
    Views:
    258
    mark tomlinson
    mark tomlinson
    Apr 20, 2019
  18. Paul Holwegner

    Unresolved M999 error

    Paul Holwegner, Apr 10, 2019
    Replies:
    11
    Views:
    345
    mark tomlinson
    mark tomlinson
    Apr 13, 2019
  19. 4sfaloth

    Unresolved Grinding noise while printing

    4sfaloth, Apr 8, 2019
    Replies:
    3
    Views:
    306
    Geof
    Geof
    Apr 8, 2019
  20. grant

    Unresolved Layer shifting, fan problem

    grant, Apr 13, 2018
    Replies:
    2
    Views:
    197
    grant
    grant
    Apr 13, 2018
Showing threads 1 to 20 of 1,057

Thread Display Options

Loading...
Page 1 of 53