1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Simplify 3d

Discussion in 'Software' started by John Rygg, Dec 6, 2013.

Page 7 of 24
  1. lemuba

    lemuba Active Member

    Joined:
    Jun 22, 2014
    Messages:
    127
    Likes Received:
    135
    Startcode with Auto Bed Level (2 Switches):

    G28 ; Home all axes

    G1 Z5 F5000 ;lift nozzle

    G28 Z0 ; Home Z again in case there was filament on nozzle

    G29 ; Autocalibrate bed

    G1 Z0.8 ; Adjust Z offset

    G92 Z0 ; Define new Z home

    End Code:

    M104 S0 ; turn off extruder

    M140 S0 ; turn off bed

    G28 X0 ; home X axis

    M84 ; disable motors
     
    #121 lemuba, Aug 29, 2014
  2. Herman Kristanto

    Herman Kristanto New Member

    Joined:
    Mar 14, 2014
    Messages:
    5
    Likes Received:
    0
    I did quick test with my "PLA Only" Robo 3D
    Left Model - S3D Slicing
    Right Model - Slic3r with MC

    General Setting is the same equal:
    Temp 195C
    No Heated Bed - Platform using 3M Ivory Tape and UHU GlueStick
    Res 0,15mm
    Infill 25%
    Speed 60mm/s (S3D - 3600mm/min)

    I already optimized the S3D profile. But I will tuning again to get rid of very small blobing.
     

    Attached Files:

    #122 Herman Kristanto, Aug 29, 2014
  3. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    EDIT PROCESS then ->SCRIPTS/ENDING GCODE

    M104 S0 ; turn off extruder
    M140 S0 ; turn off bed
    G28 X0 Y0
    M84 ; disable motors
     
    #123 mark tomlinson, Aug 30, 2014
  4. Invertmast

    Invertmast Active Member

    Joined:
    Apr 21, 2014
    Messages:
    109
    Likes Received:
    58
    Thanks guys!
     
    #124 Invertmast, Aug 31, 2014
  5. Herman Kristanto

    Herman Kristanto New Member

    Joined:
    Mar 14, 2014
    Messages:
    5
    Likes Received:
    0
    Anyone tested change Filament in the middle of Print using S3D?? I try to test that out? My current unit is used for printing customer - will try this weekend.
     
    #125 Herman Kristanto, Sep 4, 2014
  6. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    You can even pause/restart prints started from the SD card so I doubt it is a problem.
     
    #126 mark tomlinson, Sep 5, 2014
  7. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    Im on the fence about this. I could barely afford this if I got it as a poor college student. And my job has invested a bunch in my Pinter so I.can't ask them to grab this... So... But I'm sick of repetir. I have a load of work ahead if me this year..... Ahh I'm done explaining .... Push me over the fence. CONVINCE me :p
     
    #127 collin, Sep 25, 2014
  8. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    They have support people who actually read and respond (intelligently) during the work-week.
    Had one case where they fixed a model for me. Not a slicer issue, but a bad model that Netfab didn't complain about (at least not the free version).
    They got it printable in less than a day (they repaired the model and showed me some of the more advanced settings in the slicer to play with in the future).
     
    #128 mark tomlinson, Sep 26, 2014
  9. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    im going to pull from savings for this if i buy it :p >good decisions
     
    #129 collin, Sep 26, 2014
  10. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    @Mike Kelly you use bed leveling and simplify 3d right?
     
    #130 collin, Sep 26, 2014
  11. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,276
    I've been using cura lately. I haven't really bothered to configured Simplify3d for my home printer
     
    #131 Mike Kelly, Sep 26, 2014
    2 people like this.
  12. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    @collin - You should just be able to add the auto-leveling startup GCode and be done with it.
    There are a few on here using that combo so someone can comment.

    I am getting ready to add @Mike Kelly auto-level mod during some printer down-time just to keep up with the Jones :)
    I just have not gotten to it, yet.
     
    #132 mark tomlinson, Sep 26, 2014
    2 people like this.
  13. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    You haven't used the auto level yet :p i guess i knew that but it still surprises me.
     
    #133 collin, Sep 26, 2014
  14. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    I think i made my decision, my boss just dropped another project on my desk... this one will require support material... Im getting it!
     
    #134 collin, Sep 27, 2014
  15. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    Just got it, best support materiel ive ever freaking seen.
     
    #135 collin, Sep 28, 2014
    3 people like this.
  16. cosber

    cosber Active Member

    Joined:
    Jun 20, 2013
    Messages:
    300
    Likes Received:
    87
    How did you figure your Z offset? I'm sure it's posted around here someplace, but since you're using Simplify, which I just bought, I'd like to hear your method.
     
    #136 cosber, Oct 5, 2014
  17. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    honestly? just trial and error XD
     
    #137 collin, Oct 6, 2014
  18. cosber

    cosber Active Member

    Joined:
    Jun 20, 2013
    Messages:
    300
    Likes Received:
    87
    I was afraid you'd say that!
     
    #138 cosber, Oct 6, 2014
  19. collin

    collin New Member

    Joined:
    Mar 21, 2014
    Messages:
    313
    Likes Received:
    86
    You can home in on it pretty quick tho, just try somthing if the heads too close or far away you will notice. then tune by .1mm at a time then by .05 to fine tune it.
     
    #139 collin, Oct 7, 2014
  20. cosber

    cosber Active Member

    Joined:
    Jun 20, 2013
    Messages:
    300
    Likes Received:
    87
    I see that there is an offset box in the software itself. Do you use that or put it in the startup code?
     
    #140 cosber, Oct 7, 2014
Page 7 of 24

Share This Page