1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Questions about the cable connecting on board

Discussion in 'Technical Support' started by Masayuki Arakawa, Sep 1, 2013.

  1. Masayuki Arakawa

    Masayuki Arakawa New Member

    Joined:
    Sep 1, 2013
    Messages:
    6
    Likes Received:
    0
    My printer is fully assembled & calibrated type.
    But I have not been able to use it yet because of there is a trouble.
    So,I checked board of printer.

    Then I found out difference points about the cable connecting position on board.
    Please tell me the correct connecting position.
    2013.jpg

    note:
    -USB driver :installed
    -Rapetier-host V9.0C:installed

    -OS:Win7Pro SP1 64bit
     
  2. Harry

    Harry Team ROBO 3D
    Staff Member

    Joined:
    Feb 13, 2013
    Messages:
    807
    Likes Received:
    180
    Hey Masayuki, I have pointed out this post to the correct department to help you out and get this question answered.
     
    3 people like this.
  3. Masayuki Arakawa

    Masayuki Arakawa New Member

    Joined:
    Sep 1, 2013
    Messages:
    6
    Likes Received:
    0
    Hey harry

    How long time you need to response this question?
    I wander why your team need that long time to response this question .
    Even though this module is created by your team.

    Best Regards,
    Masayuki
     
  4. Harry

    Harry Team ROBO 3D
    Staff Member

    Joined:
    Feb 13, 2013
    Messages:
    807
    Likes Received:
    180
    Hey Masayuki, I am so sorry. I forgot to follow up with you on this question with the team. Thanks so much for your patience and I am going to get them on this today or tomorrow at the latest. Thanks again for your patience.
    - Harry
     
  5. Masayuki Arakawa

    Masayuki Arakawa New Member

    Joined:
    Sep 1, 2013
    Messages:
    6
    Likes Received:
    0
    Hey Harry.
    Please response!:(

    Best Regards,
    Masayuki

     
  6. Coby Robo 3D

    Coby Robo 3D Administrator
    Staff Member

    Joined:
    Feb 20, 2013
    Messages:
    75
    Likes Received:
    108
    Masayuki,

    Is this a PLA or ABS machine?
     
  7. Coby Robo 3D

    Coby Robo 3D Administrator
    Staff Member

    Joined:
    Feb 20, 2013
    Messages:
    75
    Likes Received:
    108
    It looks like you have a PLA machine, in which case, the wires are correctly wired
     
  8. Coby Robo 3D

    Coby Robo 3D Administrator
    Staff Member

    Joined:
    Feb 20, 2013
    Messages:
    75
    Likes Received:
    108
    The YouTube videos are for a printer with a heat bed
     
  9. Masayuki Arakawa

    Masayuki Arakawa New Member

    Joined:
    Sep 1, 2013
    Messages:
    6
    Likes Received:
    0

    hey Coby RoBo 3D.

    >this is PLA machine.
     
  10. Masayuki Arakawa

    Masayuki Arakawa New Member

    Joined:
    Sep 1, 2013
    Messages:
    6
    Likes Received:
    0

    hey Coby RoBo 3D

    thanks to reply.
    Ok.
    I'll retry and checking pc settings about 3d printer .
     

Share This Page