1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Solved Will these work.

Discussion in 'General Questions' started by jonnyb44, Feb 26, 2016.

  1. jonnyb44

    jonnyb44 Member

    Joined:
    Feb 11, 2016
    Messages:
    75
    Likes Received:
    16
    #1 jonnyb44, Feb 26, 2016
  2. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    Yes in both a Hexagon and in an E3D
     
    #2 WheresWaldo, Feb 26, 2016
  3. jonnyb44

    jonnyb44 Member

    Joined:
    Feb 11, 2016
    Messages:
    75
    Likes Received:
    16
    Perfect... Since I had already ordered them.


    Sent from my iPhone using Tapatalk
     
    #3 jonnyb44, Feb 27, 2016
  4. jonnyb44

    jonnyb44 Member

    Joined:
    Feb 11, 2016
    Messages:
    75
    Likes Received:
    16
    So I'm running cura do I have to change anything besides the nozzle size on the setup screen???


    Sent from my iPhone using Tapatalk
     
    #4 jonnyb44, Mar 1, 2016
  5. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Nozzle size and sometimes speed on my machine and z offset need tweaked. For instance I run 50-80mm/s .4 nozzle and 40-60 mm/s .8 nozzle
     
    #5 Geof, Mar 1, 2016
  6. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Keep in mind thatsmy machine and it will vary from machine to machine and operator to operator :)
     
    #6 Geof, Mar 1, 2016
  7. jonnyb44

    jonnyb44 Member

    Joined:
    Feb 11, 2016
    Messages:
    75
    Likes Received:
    16
    Thank you I'll give it a shot. I tend to print slow anyways under 60. Seems to make some rattle noise over that seems to print fine I just don't like the noises it makes over that. I did send in a parts request to robo for new bearings on the x carriage hoping that fixes it.


    Sent from my iPhone using Tapatalk
     
    #7 jonnyb44, Mar 1, 2016
  8. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    I replaced those and the y bearings and when this set wears out ill do @WheresWaldo threadin mods for his ultra quiet bushings
     
    #8 Geof, Mar 1, 2016
  9. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    Layer height has a relationship to nozzle diameter. If you change the nozzle diameter significantly you will want to test and see what size works best for you. Somewhere around the 50% mark works best for me.
     
    #9 mark tomlinson, Mar 2, 2016
    Geof likes this.
  10. Greg Howard

    Greg Howard Member

    Joined:
    Feb 15, 2016
    Messages:
    37
    Likes Received:
    4
    What nozzle size is standard with the R1? .5?
     
    #10 Greg Howard, Mar 7, 2016
  11. jonnyb44

    jonnyb44 Member

    Joined:
    Feb 11, 2016
    Messages:
    75
    Likes Received:
    16
    .4


    Sent from my iPhone using Tapatalk
     
    #11 jonnyb44, Mar 7, 2016
    Greg Howard and mark tomlinson like this.
  12. Greg Howard

    Greg Howard Member

    Joined:
    Feb 15, 2016
    Messages:
    37
    Likes Received:
    4
    I must have missed that in the documentation. I looked in the documentation and user guides, even the replacement extruder product info but could not find it.
    Thanks
     
    #12 Greg Howard, Mar 7, 2016
  13. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,276
    They're not exactly known for documenting
     
    #13 Mike Kelly, Mar 8, 2016
    GAmbrosio, WheresWaldo, mark tomlinson and 1 other person like this.
  14. GAmbrosio

    GAmbrosio Active Member

    Joined:
    Feb 22, 2016
    Messages:
    238
    Likes Received:
    79
    No kidding mine came with a printed manual which I now use to block the parts when I spray hairspray on the bed. Utterly useless. Their getting started video was more informative.


    Sent from my iPhone using Tapatalk
     
    #14 GAmbrosio, Mar 9, 2016
    jonnyb44 likes this.

Share This Page