1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Solved Problem with Simplify3D

Discussion in 'Troubleshooting' started by Shane Simino, Dec 13, 2016.

Thread Status:
Not open for further replies.
  1. Shane Simino

    Shane Simino Member

    Joined:
    Jun 23, 2016
    Messages:
    92
    Likes Received:
    26
    Help. I tried contacting Simplify, but I'm not a patient man. They say they'll respond in 24 hours. Anyway, I'm running into a problem on some of my models on Simplify. I believe it has to do with the surface normals not being correct. I tried fixing them all, but I can't fix some of them. The model slices fine with mattercontrol, but not Simplify. It splits it apart and adds infill where there should be nothing. Look at this side view. That's supposed to be a 45, but it breaks the model and the part is unprintable. Any suggestions? I've tried using their repair tools with no luck. side view.JPG
     
    #1 Shane Simino, Dec 13, 2016
  2. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    #2 mark tomlinson, Dec 13, 2016
    Shane Simino likes this.
  3. Shane Simino

    Shane Simino Member

    Joined:
    Jun 23, 2016
    Messages:
    92
    Likes Received:
    26
    Thank you. I'll give it a shot.
     
    #3 Shane Simino, Dec 13, 2016
  4. Shane Simino

    Shane Simino Member

    Joined:
    Jun 23, 2016
    Messages:
    92
    Likes Received:
    26
    You are the man Mark! That worked. Can I just put in a direct line to your house? Kind of like a bat phone. LOL
     
    #4 Shane Simino, Dec 13, 2016
    mark tomlinson and Geof like this.
  5. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    #5 Geof, Dec 13, 2016
  6. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    a bat phone would really cool.

    ;)
     
    #6 mark tomlinson, Dec 13, 2016
    Geof likes this.
  7. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    can I get one of them while were at it?
     
    #7 Geof, Dec 14, 2016
  8. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    #8 mark tomlinson, Dec 14, 2016
  9. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    First print on delta !
     
    #9 Geof, Dec 14, 2016
Thread Status:
Not open for further replies.

Share This Page