1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by 0ryanx

  1. 0ryanx
    Post

    Unanswered PET-G Advice

    Sorry, I should have thought of that. I'm using a R1+ with a 0.4mm nozzle, Extruder at 240, Bed at 80, 0.2mm layer height, +0.04mm Z-Offset,...
    Post by: 0ryanx, Mar 15, 2018 in forum: Troubleshooting
  2. 0ryanx
    Thread

    Unanswered PET-G Advice

    I've heard a lot of great things about PET-G, about how easy it is to print with and how strong it is. I've got the printing part down fairly...
    Thread by: 0ryanx, Mar 14, 2018, 2 replies, in forum: Troubleshooting
  3. 0ryanx
    Post

    Partial Answer Extruder Motor Makes Grinding Sound

    Adjusting the voltage didn't help; the noise just got louder. Anything else that might help?
    Post by: 0ryanx, Feb 4, 2018 in forum: Troubleshooting
  4. 0ryanx
    Post

    Print Quality

    It looks like you're over extruding a bit. Did you calibrate your extruder? I use MatterControl to make changes to my EPROM, and these...
    Post by: 0ryanx, Feb 4, 2018 in forum: Troubleshooting
  5. 0ryanx
    Thread

    Partial Answer Extruder Motor Makes Grinding Sound

    I've been printing on my Robo 3D R1+ for a couple of years, now. When I try to print today, though, the extrude makes a horrid grinding noise,...
    Thread by: 0ryanx, Feb 4, 2018, 3 replies, in forum: Troubleshooting
  6. 0ryanx
    Post

    Solved Printer Stops Printing and Lights Turn Off

    I think I finally figured it out. A while back, I replaced the parts fan to better cool the plastic as it printed, and it looks like I didn't...
    Post by: 0ryanx, Jan 21, 2018 in forum: Troubleshooting
  7. 0ryanx
    Post

    Solved Printer Stops Printing and Lights Turn Off

    No, this is a separate issue. The G Code console indicates is still printing and is not giving the temp error you're talking about. The printer...
    Post by: 0ryanx, Jan 21, 2018 in forum: Troubleshooting
  8. 0ryanx
    Thread

    Solved Printer Stops Printing and Lights Turn Off

    For the last 3 days, my printer will start printing, then at some random point in the print (mostly near the beginning of the print, sometimes in...
    Thread by: 0ryanx, Jan 21, 2018, 6 replies, in forum: Troubleshooting
  9. 0ryanx
    Post

    Unresolved EXTRUDER GEAR AND MOTOR GRINDING

    I had a similar issue with mine, and found out that the z-step value within the EEPROM was set too high. If the motor swap doesn't fix it, you...
    Post by: 0ryanx, Sep 26, 2016 in forum: Troubleshooting
  10. 0ryanx
    Post

    Solved Can't update Printer EPRROM

    Ah, I see. Thank you. I did a print of the quick-release plate the E3D V6 hotend needs, and it came out pretty nice. Thanks for all the help,...
    Post by: 0ryanx, Sep 24, 2016 in forum: Troubleshooting
  11. 0ryanx
    Post

    Solved Can't update Printer EPRROM

    And that firmware is ok to use on the R1+? I ask only because it warns not to use it on the R1+.
    Post by: 0ryanx, Sep 24, 2016 in forum: Troubleshooting
  12. 0ryanx
    Post

    Solved Can't update Printer EPRROM

    Ok, so dumb question: which file is the lead screw firmware? I see the R1+ and the R1 (which says not to use if you have the R1+), or is it...
    Post by: 0ryanx, Sep 24, 2016 in forum: Troubleshooting