1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by 4sfaloth

  1. 4sfaloth
    Post

    Unresolved R1+ temp fell too much... but hotend is good

    @mark tomlinson and @Rod Smith thank you both for your inputs. @mark tomlinson I have turned the printer around to get access to the RAMPs board...
    Post by: 4sfaloth, Dec 1, 2020 in forum: Troubleshooting
  2. 4sfaloth
    Thread

    Unresolved R1+ temp fell too much... but hotend is good

    Hi all, A few weeks ago my R1+ started stopping mid-print with the Extruder switched off. Temperature fell too much during print error. Due to...
    Thread by: 4sfaloth, Nov 28, 2020, 4 replies, in forum: Troubleshooting
  3. 4sfaloth
    Post

    Unresolved Hotend Assembly

    Hum... Should I try to tighten it when heated perhaps then?
    Post by: 4sfaloth, Oct 31, 2020 in forum: Troubleshooting
  4. 4sfaloth
    Post

    Unresolved Hotend Assembly

    Hi Mark, thanks for stepping in once again. I've tried securing the thermistor with kapton tape, but it still failed. Either it was not secure...
    Post by: 4sfaloth, Oct 31, 2020 in forum: Troubleshooting
  5. 4sfaloth
    Thread

    Unresolved Hotend Assembly

    Hi all, I am having midprint hotend thermistor errors (temperature fell too much during print blablabla). For now I just intended to make sure...
    Thread by: 4sfaloth, Oct 31, 2020, 5 replies, in forum: Troubleshooting
  6. 4sfaloth
    Post

    Partially Solved Robo 3d R1+ need Mattercontrol settings help

    You can download MC 1.3.0 that came with the printer from here: https://we.tl/t-r3Lv8r4zmr (will only be available for a few days I think) As for...
    Post by: 4sfaloth, Jul 20, 2020 in forum: Troubleshooting
  7. 4sfaloth
    Thread

    Unanswered Issues with new filament

    Hi, I've recently bought a new filament spool from a local store and it's been a nightmare to print with. It's supposed to be regular PLA, but...
    Thread by: 4sfaloth, Jul 19, 2020, 1 replies, in forum: Troubleshooting
  8. 4sfaloth
    Post

    Partially Solved Robo 3d R1+ need Mattercontrol settings help

    I remember my R1+ printer came with a specific version of MatterControl on a SD card ou a USB pen. I'm pretty sure I still have those lying...
    Post by: 4sfaloth, Jul 19, 2020 in forum: Troubleshooting
  9. 4sfaloth
    Post

    Solved Misaligned Print

    yeah, that's what I did. Ok thanks :)
    Post by: 4sfaloth, Jun 28, 2020 in forum: Troubleshooting
  10. 4sfaloth
    Post

    Solved Misaligned Print

    Alright I believe it's done. Just to make sure, you're talking about the screws signaled in the attached picture, right? Only the only signalled...
    Post by: 4sfaloth, Jun 28, 2020 in forum: Troubleshooting
  11. 4sfaloth
    Post

    Solved Thermistor stopped working (again)

    I forgot to update this but in the end I had to replace the hotend (couldn't remove the previous thermistor from it, which I clearly overtightened...
    Post by: 4sfaloth, Jun 28, 2020 in forum: Troubleshooting
  12. 4sfaloth
    Post

    Solved Misaligned Print

    not sure what you "long enough time" would be :) I've had the printer for almost 2 years now, and never made any adjustments to the belts/screws....
    Post by: 4sfaloth, Jun 24, 2020 in forum: Troubleshooting