1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Allelujah

  1. Allelujah
    Post

    Solved Unidentified Part?

    Alrighty thanks guys. Is there really no need for it? Will it be safe to continue printing without it?
    Post by: Allelujah, Sep 9, 2018 in forum: Troubleshooting
  2. Allelujah
    Thread

    Solved Unidentified Part?

    Hello everyone. Its been about a year or two since i last been on the forums. So I been enjoying my Robo R1+ for the past 2 years now and I was...
    Thread by: Allelujah, Sep 8, 2018, 7 replies, in forum: Troubleshooting
  3. Allelujah
    Post

    Answered Nozzle Replacement

    Thanks XD I plan on printting some very small details for my Gunpla Swords So i hope it does just that :D. Also bought a .25 and a .8 nozzle. The...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  4. Allelujah
    Post

    Answered Nozzle Replacement

    Alrighty. That sounds like a problem for future self to deal with tomorrow. Thanks for the help and advice Mark.
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  5. Allelujah
    Post

    Answered Nozzle Replacement

    OK so thats 2 things i should change, what should I change them to? Or is that something i need to ask somewhere else? I assume there is a long...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  6. Allelujah
    Post

    Answered Nozzle Replacement

    Yeah I went from the normal default nozzle size to a 0.15 And I think I found where i need to make changes but not sure if there is anywhere else...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  7. Allelujah
    Post

    Answered Nozzle Replacement

    Alrighty. Also I know there is someone on the forums that uses Matter Control as well but his name escapes me, I hope he looks at this thread...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  8. Allelujah
    Post

    Answered Nozzle Replacement

    Does the shaft part of the nozzle need to be fully in the block part of the hot end? Beacause I do not have the hex part of the Nozzle touching...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  9. Allelujah
    Post

    Answered Nozzle Replacement

    Alrighty lol I have a pliers and a wrench would that work? Dont have 2 wrenches unfortunately
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  10. Allelujah
    Post

    Answered Nozzle Replacement

    Alrighty I will try and watch the vid. I am mostly deaf so hearing what the person says will be an issue if he says something important. I will...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  11. Allelujah
    Thread

    Answered Nozzle Replacement

    Hello everyone, I am back yet again with another few questions. So my new nozzles came in the mail today and I am eagerly waiting to install one...
    Thread by: Allelujah, Feb 4, 2017, 20 replies, in forum: General Questions
  12. Allelujah
    Thread

    Solved Types of Filament

    Hello everyone. Got another question for you all. Well a couple questions. First up is what are all the different types of filament can the Robo...
    Thread by: Allelujah, Jan 7, 2017, 2 replies, in forum: General Questions