1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by ammulder

  1. ammulder
    Post

    Layer Alignment

    I think I was referred to "tier 2" on Wednesday... I haven't heard a peep since (not even, like, a confirmation that it was in a tier 2 queue)....
    Post by: ammulder, Feb 13, 2017 in forum: Troubleshooting
  2. ammulder
    Post

    Layer Alignment

    OK, I dug up a small test model on thingiverse, and printed one (left) with the Robo Normal profile in Cura 2.3.1 on the Mac (forgetting that it...
    Post by: ammulder, Feb 13, 2017 in forum: Troubleshooting
  3. ammulder
    Post

    Layer Alignment

    OK, I see loads of speed, acceleration, and jerk settings in Cura. My plan is to halve print speed, print acceleration, and print jerk (and check...
    Post by: ammulder, Feb 8, 2017 in forum: Troubleshooting
  4. ammulder
    Post

    Layer Alignment

    Well, it is true that the Replicator was a costlier printer. I just figure that today's printer should be at least as good. I've heard such...
    Post by: ammulder, Feb 8, 2017 in forum: Troubleshooting
  5. ammulder
    Post

    Layer Alignment

    Here are my pics to try to clarify this issue. I printed some with the Robo Cura 2.3.1 distribution for Windows, at .15 layer height (same as I...
    Post by: ammulder, Feb 8, 2017 in forum: Troubleshooting
  6. ammulder
    Post

    Layer Alignment

    So I talked to Robo on the phone, and the person there said he'd send the issue to Level 2 and they'd e-mail me back within a few business days.
    Post by: ammulder, Feb 8, 2017 in forum: Troubleshooting
  7. ammulder
    Post

    Safe to update Octoprint?

    So if I read that (#4) right, it is actually OctoPrint on the Pi that is controlling the touch screen on the C2?
    Post by: ammulder, Feb 8, 2017 in forum: Software
  8. ammulder
    Post

    Safe to update Octoprint?

    It seems like there are a lot of moving parts: The "firmware", which I guess means the customized Marlin firmware, running on an Arduino...
    Post by: ammulder, Feb 8, 2017 in forum: Software
  9. ammulder
    Post

    Safe to update Octoprint?

    So, how did you manage to install RoboLCD 1.3.1? Because OctoPrint tells me there are no updates available. I would be happy to manually install...
    Post by: ammulder, Feb 8, 2017 in forum: Software
  10. ammulder
    Post

    Safe to update Octoprint?

    I'm not sure what that's the version of -- I have OctoPrint 1.3.1 and RoboLCD 1.3.0 (and RoboOS 1.0.3)
    Post by: ammulder, Feb 7, 2017 in forum: Software
  11. ammulder
    Post

    Safe to update Octoprint?

    Crap. Mine won't do that. I've done all the updates in OctoPrint -- I tried telling it to look for updates and it said all up to date. But the...
    Post by: ammulder, Feb 7, 2017 in forum: Software
  12. ammulder
    Post

    Layer Alignment

    Interestingly, I see the settings provided by @Cory Harpell have 90% flow rate... Maybe I should try that too.
    Post by: ammulder, Feb 7, 2017 in forum: Troubleshooting
  13. ammulder
    Post

    Safe to update Octoprint?

    Some down sides I've noticed (though I'm not sure whether they were there before): The Utilities / Update screen shows a RoboOS update available...
    Post by: ammulder, Feb 7, 2017 in forum: Software
  14. ammulder
    Post

    Layer Alignment

    I did the calibration routine. He recommended extruding 100mm and measuring how much filament it used. I measured 99mm. I don't think that...
    Post by: ammulder, Feb 7, 2017 in forum: Troubleshooting
  15. ammulder
    Post

    How to update firmware

    I put that into OctoPrint, though I assume that would only be used if OctoPrint slices the model, so I probably I need to put it into Cura too. I...
    Post by: ammulder, Feb 7, 2017 in forum: Troubleshooting