1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Arthur Smith

  1. Arthur Smith
    Post

    Unanswered I give up - New Hotend Help

    Okay, sorry about the long delay. I wrote the post after trying the better filament, but when I had no money to try anything else. I have a bit...
    Post by: Arthur Smith, Jan 17, 2017 in forum: Troubleshooting
  2. Arthur Smith
    Thread

    Unanswered I give up - New Hotend Help

    Okay, I bought me Robo3D 2 years ago. I got 3 prints out of it, but it kept jamming. I was told then, that was a common issue and I should...
    Thread by: Arthur Smith, Dec 16, 2016, 9 replies, in forum: Troubleshooting
  3. Arthur Smith
    Post

    Repetier Host Setup

    Where do I put the .ini file?
    Post by: Arthur Smith, Mar 17, 2016 in forum: Software
  4. Arthur Smith
    Post

    E3D v6 Information, Installation Guides, and Review

    Got the .ini now where do I put it?
    Post by: Arthur Smith, Mar 17, 2016 in forum: Mods and Upgrades
  5. Arthur Smith
    Post

    E3D v6 Information, Installation Guides, and Review

    Okay... Jam cleared, Matter Control uninstalled, Repetier-Host installed, retry = jam. So what do I do in Repetier-Host?
    Post by: Arthur Smith, Mar 17, 2016 in forum: Mods and Upgrades
  6. Arthur Smith
    Post

    E3D v6 Information, Installation Guides, and Review

    I saw a picture of this, and I assume a solution, but cannot find it. Here's what I I'm getting when it clogs. The filament kind of smooshes out...
    Post by: Arthur Smith, Mar 17, 2016 in forum: Mods and Upgrades
  7. Arthur Smith
    Post

    E3D v6 Information, Installation Guides, and Review

    Still doing the same. Is there anything i need to do to the software or firmware after the e3D install?
    Post by: Arthur Smith, Mar 16, 2016 in forum: Mods and Upgrades
  8. Arthur Smith
    Post

    E3D v6 Information, Installation Guides, and Review

    Okay.... One step closer. The cable was too tight so when it went all the way over, it lifted up just enough. SO, now its doing the leveling...
    Post by: Arthur Smith, Mar 16, 2016 in forum: Mods and Upgrades
  9. Arthur Smith
    Post

    E3D v6 Information, Installation Guides, and Review

    Okay, got that worked out, had 2 wires switched. Now when it does the bed leveling, the left 2 points of each row work correct but the right...
    Post by: Arthur Smith, Mar 16, 2016 in forum: Mods and Upgrades
  10. Arthur Smith
    Post

    Answered *READ ME* My ROBO doesn't auto level correctly!? FAQ

    x_min: open y_min: TRIGGERED z_min: TRIGGERED I reversed those two wires and now all 3 show open. Now when it auto levels, the left and the...
    Post by: Arthur Smith, Mar 16, 2016 in forum: Troubleshooting
  11. Arthur Smith
    Post

    Answered *READ ME* My ROBO doesn't auto level correctly!? FAQ

    Total Newbie here, don't assume I know ANYTHING! I got my Robo 3d v1 and was having jamming issues. It was suggested to upgrade to the E3d v6...
    Post by: Arthur Smith, Mar 14, 2016 in forum: Troubleshooting
  12. Arthur Smith
    Post

    E3D v6 Information, Installation Guides, and Review

    Everything looks good to me. Here is the bed. Both red and black wires are attached and there is no space so the buttons would seem pressed...
    Post by: Arthur Smith, Mar 12, 2016 in forum: Mods and Upgrades
  13. Arthur Smith
    Post

    E3D v6 Information, Installation Guides, and Review

    Sigh... I was right. so now its heating but when I tell it to print, when it tries to auto level, at each point it goes up 10mm, then to the next...
    Post by: Arthur Smith, Mar 12, 2016 in forum: Mods and Upgrades
  14. Arthur Smith
    Post

    E3D v6 Information, Installation Guides, and Review

    Its finally heating... Give me a minute, I'm sure I'll find something else...
    Post by: Arthur Smith, Mar 12, 2016 in forum: Mods and Upgrades