1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by astro boy

  1. astro boy
    Post

    Answered firmware error / e3d v6 upgrade

    I finally got a chance to get everything squared away and now its up and running. Printing better than before in fact. I finally added some shims...
    Post by: astro boy, Feb 20, 2019 in forum: Troubleshooting
  2. astro boy
    Post

    Answered firmware error / e3d v6 upgrade

    Thanks Waldo, Those values are what I have currently, but after some experimenting I have found that I don't need to change anything it seems. I...
    Post by: astro boy, Feb 18, 2019 in forum: Troubleshooting
  3. astro boy
    Post

    Answered firmware error / e3d v6 upgrade

    Can anyone tell me what their default acceleration settings are? my acceleration says 1300 for all, I assume I'm changing values under movement...
    Post by: astro boy, Feb 18, 2019 in forum: Troubleshooting
  4. astro boy
    Post

    Answered firmware error / e3d v6 upgrade

    Thanks Mark & Waldo, I did some research last night on the forum and came to the same conclusion, that it might be a stepper driver issue as well....
    Post by: astro boy, Feb 16, 2019 in forum: Troubleshooting
  5. astro boy
    Post

    Answered firmware error / e3d v6 upgrade

    ok... my status is that I've run pid autotune and changed the values in config.h, uploaded and tried to start printing. well my extruder stepper...
    Post by: astro boy, Feb 16, 2019 in forum: Troubleshooting
  6. astro boy
    Post

    Answered firmware error / e3d v6 upgrade

    ok well... It compiled with no errors or warnings, I made the changes and uploaded with apparently no issue whatsoever. Yay for our side! I didn't...
    Post by: astro boy, Feb 7, 2019 in forum: Troubleshooting
  7. astro boy
    Post

    Answered firmware error / e3d v6 upgrade

    great, thanks guys! I'm going to try again tonight and I'll post my results. Hopefully everything works out. 1 other question, for those who have...
    Post by: astro boy, Feb 7, 2019 in forum: Troubleshooting
  8. astro boy
    Post

    Answered firmware error / e3d v6 upgrade

    Thanks again guys, your always so helpful and have gotten me out of jams before. I’ll try the code file you sent tonight Waldo. To be clear, I...
    Post by: astro boy, Feb 7, 2019 in forum: Troubleshooting
  9. astro boy
    Post

    Answered firmware error / e3d v6 upgrade

    Thanks Waldo and Mark, to answer Waldo’s question, I went to the robo help forum where the thread is called updating firmware with Arduino....
    Post by: astro boy, Feb 7, 2019 in forum: Troubleshooting
  10. astro boy
    Thread

    Answered firmware error / e3d v6 upgrade

    Hi All, I bought a e3d v6 hotend for my Robo r1+ and want to change the firmware according to the forum and e3d site for temperature values. My...
    Thread by: astro boy, Feb 6, 2019, 21 replies, in forum: Troubleshooting
  11. astro boy
    Post

    Answered bed temperature behavior

    Thanks, I'll see if this helps me. I noticed my Hotend drifting a little as well. Not sure if it's related to this but I'll see what happens....
    Post by: astro boy, Apr 1, 2018 in forum: Troubleshooting
  12. astro boy
    Thread

    Answered bed temperature behavior

    I have the robo 3d r1+ using pla @ 200/bed @60 I just wanted to ask, is it common for the heated bed temperature to rise beyond 60 degrees during...
    Thread by: astro boy, Mar 29, 2018, 2 replies, in forum: Troubleshooting
  13. astro boy
    Post

    Answered Extruder fan... always on?

    Thanks Mark Sorry about not posting a new thread on this. I thought about it but figured it was somewhat related. I'm sure there will be more...
    Post by: astro boy, Feb 9, 2018 in forum: Troubleshooting