1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Avrution

  1. Avrution
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    So would it just be / 2 to end up in the center? Edit - yup, that does it. Thanks!
    Post by: Avrution, Mar 26, 2022 in forum: Mods and Upgrades
  2. Avrution
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    What would I need to edit in order for G28 to home in the center of the bed instead of at the corner (22,24ish)?
    Post by: Avrution, Mar 25, 2022 in forum: Mods and Upgrades
  3. Avrution
    Post

    Unresolved Problem with printer or actual print file?

    Seems something is just being lost in translation. I imported the file into Fusion 360 and it thinks it is 200mm versus the 20mm that it actually is.
    Post by: Avrution, Apr 12, 2021 in forum: Troubleshooting
  4. Avrution
    Post

    Unresolved Problem with printer or actual print file?

    Looks the same before and after. The only thing I see that might be an issue is that when I import the file into S3D it mentions how the part...
    Post by: Avrution, Apr 12, 2021 in forum: Troubleshooting
  5. Avrution
    Thread

    Unresolved Problem with printer or actual print file?

    I designed a small object in tinkercad, since that is about the extent of my designing experience. I'd had no issues printing larger things that...
    Thread by: Avrution, Apr 11, 2021, 5 replies, in forum: Troubleshooting
  6. Avrution
    Post

    Solved R1+ / Marlin / Homing failed

    Going to consider this one closed. Started everything over, wiped settings and so far printing normally. As usual, thank you for all of the help.
    Post by: Avrution, Mar 20, 2021 in forum: Troubleshooting
  7. Avrution
    Post

    Solved R1+ / Marlin / Homing failed

    Before doing anything more I guess I need to flash the firmware to get the correct settings. I'm guessing that is why my first print freaked out...
    Post by: Avrution, Mar 19, 2021 in forum: Troubleshooting
  8. Avrution
    Post

    Solved R1+ / Marlin / Homing failed

    Which should be 254x228x200 - right? Yet mine is stopping at 238x220x200. Ah, it seems whoever did the edits for the Robo updates in Marlin set...
    Post by: Avrution, Mar 19, 2021 in forum: Troubleshooting
  9. Avrution
    Post

    Solved R1+ / Marlin / Homing failed

    Right, but it seems to be stopping at 220x and 238y. I will try and get it to halt. It never happens when I want it to.
    Post by: Avrution, Mar 19, 2021 in forum: Troubleshooting
  10. Avrution
    Post

    Solved R1+ / Marlin / Homing failed

    When the halt happens it is instant. Say if it happens after doing a G28 then as soon as I hit enter it locks the printer. Here is something I...
    Post by: Avrution, Mar 19, 2021 in forum: Troubleshooting
  11. Avrution
    Post

    Solved R1+ / Marlin / Homing failed

    Not a rod, but the plastic part of the bed frame presses against it. X goes to the switch - tap tap. The Y moves to the switch - tap tap. Then...
    Post by: Avrution, Mar 19, 2021 in forum: Troubleshooting
  12. Avrution
    Post

    Solved R1+ / Marlin / Homing failed

    The X triggers correctly each time it homes and I watched as the Y triggers - I actually had a magnet tear off when removing the bed to check...
    Post by: Avrution, Mar 19, 2021 in forum: Troubleshooting
  13. Avrution
    Post

    Solved R1+ / Marlin / Homing failed

    Little more testing - small stuff seems fine, the problem is anything larger than a few inches. It is like the thing doesn't know where the Y...
    Post by: Avrution, Mar 19, 2021 in forum: Troubleshooting
  14. Avrution
    Post

    Solved R1+ / Marlin / Homing failed

    Gotcha, for some reason I thought the stock firmware was it's own setup. Just had another halt when doing G28. Restarted without moving anything...
    Post by: Avrution, Mar 19, 2021 in forum: Troubleshooting