1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by BLKFLD

  1. BLKFLD
    Post

    R2 - nozzle crashes on the printbed

    I don’t know about your code modifications. I usually run sheets of blue tape (Amazon) to help with bed adhesion. I received a free build surface...
    Post by: BLKFLD, Mar 31, 2021 in forum: Troubleshooting
  2. BLKFLD
    Thread

    Robo 3D R1+ Mac OS recommended Slicer

    Hello. I have been running an R1+ pretty problem free with a .8 extruder and MatterControl, but lately MatterControl has taken to "timing out" in...
    Thread by: BLKFLD, Nov 10, 2020, 2 replies, in forum: General Questions
  3. BLKFLD
    Post

    R2 - nozzle crashes on the printbed

    Old Topic but some print surfaces don't trigger the IR sensor. I use blue build plate sheets most of the time. I switched today to an Overture...
    Post by: BLKFLD, Oct 26, 2020 in forum: Troubleshooting
  4. BLKFLD
    Post

    Robo R2 hot end set screw size

    I had my M3 bolt strip also. Instead of tapping for an M4 screw, which may require disassembling the carriage I simply put an m3 square nut behind...
    Post by: BLKFLD, Aug 10, 2020 in forum: General Questions
  5. BLKFLD
    Thread

    R2 usable without a screen?

    Can I do offset and bed leveling remotely? without the screen plugged in at all? or with a non functioning screen connected.? Back story: screen...
    Thread by: BLKFLD, Apr 29, 2020, 5 replies, in forum: General Questions
  6. BLKFLD
    Post

    Upgrade your Robo R2 to a capacitive 5 inch touch screen (Completed)

    Hello, I'm not a raspberry pi person, but am willing to try this out or throw my R2 from my window. Are there any more current firmware builds...
    Post by: BLKFLD, Apr 28, 2020 in forum: Projects
  7. BLKFLD
    Post

    Answered Printer Hardware Error M999

    how do you reset it after replacing the suspect thermistor?
    Post by: BLKFLD, Nov 8, 2018 in forum: Troubleshooting
  8. BLKFLD
    Post

    Adding a 2nd Hot End

    Any updates on the dual extruder kit? Robo's link is 404
    Post by: BLKFLD, Oct 27, 2017 in forum: General Questions
  9. BLKFLD
    Post

    R2 not extruding properly

    So you have to disassemble the whole thing? Is there a write up somewhere? I submitted a support request. Im not taking anything apart until I...
    Post by: BLKFLD, Aug 7, 2017 in forum: Troubleshooting
  10. BLKFLD
    Post

    R2 not extruding properly

    Everything at the extruder looks firmly connected. there are two sets of terminals on the bottom side of the extruder carriage. as viewed from the...
    Post by: BLKFLD, Aug 7, 2017 in forum: Troubleshooting
  11. BLKFLD
    Post

    R2 Click and Snapping Sounds

    Im getting that click at the hotbed bolt, my issue is likely due to a temperature problem (190°C displayed 47°C actual). How did you fix your problem?
    Post by: BLKFLD, Aug 6, 2017 in forum: Troubleshooting
  12. BLKFLD
    Post

    R2 not extruding properly

    Hello, It seems as the hotbed bolt is fine. I did have a chance to get my infrared thermometer and it seems like my extruder is only 45°C but...
    Post by: BLKFLD, Aug 6, 2017 in forum: Troubleshooting
  13. BLKFLD
    Post

    R2 not extruding properly

    I'm having an extrusion problem too. I have: - run cleaning filament through the extruder, it jammed up in the process (happens relatively easy...
    Post by: BLKFLD, Aug 6, 2017 in forum: Troubleshooting