1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Chuck Glenn

  1. Chuck Glenn
    Post

    Unresolved R1 is stopping mid print

    So note to all others, do NOT do print via USB from Cura! At least not to an R1+
    Post by: Chuck Glenn, Feb 24, 2024 in forum: Troubleshooting
  2. Chuck Glenn
    Post

    Unresolved R1 is stopping mid print

    And it completed. I guess I got my answer. Now where do I send the slightly used arduino, extra ramps, slightly used hotend with...
    Post by: Chuck Glenn, Feb 24, 2024 in forum: Troubleshooting
  3. Chuck Glenn
    Post

    Unresolved R1 is stopping mid print

    I appreciate you sticking with me Mark! I have made some hopeful progress... Based on the assumption that Cura USB printing is bugged as they...
    Post by: Chuck Glenn, Feb 24, 2024 in forum: Troubleshooting
  4. Chuck Glenn
    Post

    Unresolved R1 is stopping mid print

    Well more interesting stuff. I decided to browse the Cura forums to see if there was any serial montir, and I see tons of discussions tht USB...
    Post by: Chuck Glenn, Feb 24, 2024 in forum: Troubleshooting
  5. Chuck Glenn
    Post

    Unresolved R1 is stopping mid print

    and this if it could possibly matter [ATTACH]
    Post by: Chuck Glenn, Feb 23, 2024 in forum: Troubleshooting
  6. Chuck Glenn
    Post

    Unresolved R1 is stopping mid print

    Gotcha! Well I was just hoping it wasn't because of some kind of inherent incompatibility. I've used it quite a lot, and this behavior is new, so...
    Post by: Chuck Glenn, Feb 23, 2024 in forum: Troubleshooting
  7. Chuck Glenn
    Post

    Unresolved R1 is stopping mid print

    I always use "printing via usb" from Cura. I'm curious why MatterControl is still listed as the recommended software for the R1+ on the web site.
    Post by: Chuck Glenn, Feb 21, 2024 in forum: Troubleshooting
  8. Chuck Glenn
    Post

    Unresolved R1 is stopping mid print

    I use arduino for lots of things, but I cannot seem to get it to recognize the mega 2560 in the r1+. USB dings when I plug or unplug, but now Cura...
    Post by: Chuck Glenn, Feb 20, 2024 in forum: Troubleshooting
  9. Chuck Glenn
    Post

    Unresolved R1 is stopping mid print

    Howdy gang, and Mark! I got here because mine R1+ just stops right in the middle of printing after a couple of years now of smooth performance....
    Post by: Chuck Glenn, Feb 20, 2024 in forum: Troubleshooting
  10. Chuck Glenn
    Post

    Solved Y-Axis shifts on large prints

    well since I only have one printer and it's flaking... i just ordered the pillows from partsbuilt. After installing those I have had no skips in...
    Post by: Chuck Glenn, Feb 4, 2020 in forum: Troubleshooting
  11. Chuck Glenn
    Post

    Solved Y-Axis shifts on large prints

    ok, i went 120 clockwise, and I started a print, but then noticed the bed was wobbling a little, which was messing up the auto-level... then I...
    Post by: Chuck Glenn, Jan 30, 2020 in forum: Troubleshooting
  12. Chuck Glenn
    Post

    Solved Y-Axis shifts on large prints

    Thanks Mark, Is there any harm in using a RAMPS 1.6? Plus, I already replaced the stepper driver / A4988 for the Y and it really didn't make...
    Post by: Chuck Glenn, Jan 29, 2020 in forum: Troubleshooting
  13. Chuck Glenn
    Post

    Solved Y-Axis shifts on large prints

    ok, so I replaced the Y stepper after having to order a cable (4-pin to 6-pin), re-wiring the cable since it was wrong, installing that above...
    Post by: Chuck Glenn, Jan 29, 2020 in forum: Troubleshooting
  14. Chuck Glenn
    Post

    Solved Y-Axis shifts on large prints

    Ok, still skipping with the new driver. Next thing to try would be a new stepper motor I suppose.
    Post by: Chuck Glenn, Jan 24, 2020 in forum: Troubleshooting
  15. Chuck Glenn
    Thread

    Minor upgrades worth pursuing?

    Is there any merit to replacing the stepper drivers (which apparently are A4988 parts) with DRV8825 or another type? I saw some reviews where...
    Thread by: Chuck Glenn, Jan 24, 2020, 2 replies, in forum: General Questions