1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by EvilDrReef

  1. EvilDrReef
    Thread

    BuildTak Flexplate?

    Hi everyone! I got a BuildTak Flexplate for my R2 a long time ago, and I really like it. Not only is adhesion no longer an issue basically ever,...
    Thread by: EvilDrReef, Dec 5, 2022, 2 replies, in forum: Mods and Upgrades
  2. EvilDrReef
    Post

    Cura 4.10 Settings?

    Thanks! That did seem to help. I've printed out a few things so far, and I haven't run into any issues. The camera even works on Cura 4.10, which...
    Post by: EvilDrReef, Aug 24, 2021 in forum: Software
  3. EvilDrReef
    Thread

    Cura 4.10 Settings?

    Hey everyone! I feel like this is a question that has an answer somewhere, but I haven't been able to find it. I decided that I'd like to start...
    Thread by: EvilDrReef, Aug 18, 2021, 2 replies, in forum: Software
  4. EvilDrReef
    Post

    Failing layers due to underextrusion

    Hey everyone, thanks so much for your help. Tightening up that hex bolt really did the trick. I'll keep a much closer eye on that tension...
    Post by: EvilDrReef, Apr 28, 2020 in forum: Troubleshooting
  5. EvilDrReef
    Post

    Failing layers due to underextrusion

    Thanks for the resources! I took the lever apart, and it doesn't appear to be cracked. The back plate doesn't seem to be damaged either. What DOES...
    Post by: EvilDrReef, Apr 28, 2020 in forum: Troubleshooting
  6. EvilDrReef
    Thread

    Failing layers due to underextrusion

    I've had this problem sporadically recently. Every once in awhile, particularly towards the end of a longer print, several layers will just stop...
    Thread by: EvilDrReef, Apr 27, 2020, 5 replies, in forum: Troubleshooting
  7. EvilDrReef
    Post

    Solved Prints Deformed, Haven't Changed Settings

    Great news! The new nozzle seems to have fixed this problem! I feel bad not having thought of that in the first place, but I really really...
    Post by: EvilDrReef, Dec 11, 2019 in forum: Troubleshooting
  8. EvilDrReef
    Post

    Solved Prints Deformed, Haven't Changed Settings

    It does seem possible that nozzle wear might be my problem. The filament I extruded is measuring between .5 and .53mm, which I'm guessing means...
    Post by: EvilDrReef, Dec 10, 2019 in forum: Troubleshooting
  9. EvilDrReef
    Post

    Solved Prints Deformed, Haven't Changed Settings

    Thanks for the suggestions! I unplugged/replugged everything back in, and while it did somehow help everything to run way quieter than it was...
    Post by: EvilDrReef, Dec 9, 2019 in forum: Troubleshooting
  10. EvilDrReef
    Post

    Solved Prints Deformed, Haven't Changed Settings

    I tightened them back up and I'll do a quick test print. I should mention, though, that these problems started before I adjusted the screws, so...
    Post by: EvilDrReef, Dec 8, 2019 in forum: Troubleshooting
  11. EvilDrReef
    Post

    Solved Prints Deformed, Haven't Changed Settings

    The cold end fan runs at all times on my printer, even when it's not heated up. The part cooling fan is definitely blowing air, too. Since you...
    Post by: EvilDrReef, Dec 8, 2019 in forum: Troubleshooting
  12. EvilDrReef
    Post

    Solved Prints Deformed, Haven't Changed Settings

    Oh, gotcha! Yep, it's blowing out air down there. I can feel it coming out.
    Post by: EvilDrReef, Dec 8, 2019 in forum: Troubleshooting