1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Gage

  1. Gage
    Post

    Solved Bed Adhesion Issues

    Only other guess is that the sudden cold front in the weather here has just had that much of an impact on the humidity level in the house.
    Post by: Gage, Feb 9, 2020 in forum: Troubleshooting
  2. Gage
    Post

    Solved Bed Adhesion Issues

    I have used that wolf bite before. Worked well, almost too well as it cracked one of my glass panes upon removal. Funny enough, I thought I would...
    Post by: Gage, Feb 9, 2020 in forum: Troubleshooting
  3. Gage
    Thread

    Solved Bed Adhesion Issues

    Not sure what the issue is, and my best guess has me worried. Been printing for years using the Elmer's Purple glue stick, always been my go to...
    Thread by: Gage, Feb 8, 2020, 6 replies, in forum: Troubleshooting
  4. Gage
    Post

    Solved Printer Shutting off.

    The relic is officially back up and printing. Few tweaks need to be made, namely getting all the fine tuning back in line. But have had two...
    Post by: Gage, Jan 25, 2020 in forum: Troubleshooting
  5. Gage
    Post

    Solved Printer Shutting off.

    Well, it took some doing but I got everything switched over from the old board to the new. Was having an issue with connectivity but found the...
    Post by: Gage, Jan 24, 2020 in forum: Troubleshooting
  6. Gage
    Post

    Solved Printer Shutting off.

    Sounds almost like what I ordered from Amazon, except it was $25.
    Post by: Gage, Jan 23, 2020 in forum: Troubleshooting
  7. Gage
    Post

    Solved Printer Shutting off.

    That's true. I will probably end up ordering an all in one before long. I've got so much extra after all of this I may just build myself a second...
    Post by: Gage, Jan 23, 2020 in forum: Troubleshooting
  8. Gage
    Post

    Solved Printer Shutting off.

    Well I will just get one ordered and get cracking tomorrow.
    Post by: Gage, Jan 23, 2020 in forum: Troubleshooting
  9. Gage
    Post

    Solved Printer Shutting off.

    Yeah, the old one was good, but since I had it all apart I went ahead and switched it with a new on. I had no heat errors or gcode errors other...
    Post by: Gage, Jan 23, 2020 in forum: Troubleshooting
  10. Gage
    Post

    Solved Printer Shutting off.

    [ATTACH]So I'm guessing an R1+ just have a bead thermistor for some reason.
    Post by: Gage, Jan 23, 2020 in forum: Troubleshooting
  11. Gage
    Post

    Solved Printer Shutting off.

    I thought this was an R1+, but it has always had a glass bead thermistor. Anything else I can do to make sure I have what I think I have?
    Post by: Gage, Jan 23, 2020 in forum: Troubleshooting
  12. Gage
    Post

    Solved Printer Shutting off.

    Believe I found the culprit. I noticed a feint ozone scent this time. Looked at the RAMPS board. The plug of the ribbon cable to the bed heater is...
    Post by: Gage, Jan 23, 2020 in forum: Troubleshooting
  13. Gage
    Post

    Solved Printer Shutting off.

    Back again, new power supply installed. Got to around the same portion of the print and noticed the lights flickering slightly before everything...
    Post by: Gage, Jan 23, 2020 in forum: Troubleshooting
  14. Gage
    Post

    Solved Printer Shutting off.

    Well I just ordered a new one. I will post an update once it arrives and I can install it. Thanks for the help in narrowing it down though,...
    Post by: Gage, Jan 19, 2020 in forum: Troubleshooting