1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by GATed73

  1. GATed73
    Post

    Bed Can't Get Above 90Deg Before Error

    Here's my update. Support pointed me to level 2. They cancelled my appointment because it was obvious my pogo was screwed up. They sent me a...
    Post by: GATed73, Aug 3, 2017 in forum: Troubleshooting
  2. GATed73
    Post

    Bed Can't Get Above 90Deg Before Error

    Phone support was a bit easier than I anticipated. Lasted about 30 seconds and they said just schedule an appointment with a level 2 tech....
    Post by: GATed73, Jul 24, 2017 in forum: Troubleshooting
  3. GATed73
    Post

    Bed Can't Get Above 90Deg Before Error

    Thing is, this was printing beautifully right up until the software update. Not sure if coincidence, or what. I sent an email - will try calling...
    Post by: GATed73, Jul 23, 2017 in forum: Troubleshooting
  4. GATed73
    Post

    Bed Can't Get Above 90Deg Before Error

    I took a closer look at my pogo conectors. I think it's safe to say I have a problem - the two left pins look problematic. [ATTACH] [ATTACH]
    Post by: GATed73, Jul 23, 2017 in forum: Troubleshooting
  5. GATed73
    Post

    Bed Can't Get Above 90Deg Before Error

    Same problem just sprung up on me this morning. I've been doing only PLA prints, with the bed at about 60C. Actually, my message says Heater_ID: bed
    Post by: GATed73, Jul 16, 2017 in forum: Troubleshooting
  6. GATed73
    Post

    Support Material Prints

    That worked very well. I changed support Z distance from .16mm to .2mm and the result is much better. Thanks!
    Post by: GATed73, Jun 17, 2017 in forum: Troubleshooting
  7. GATed73
    Thread

    Support Material Prints

    Has anyone found settings that play nice with support material? I'm having a hard time with support material coming out very stringy, being very...
    Thread by: GATed73, Jun 17, 2017, 4 replies, in forum: Troubleshooting
  8. GATed73
    Post

    Some issues with the R2?

    eh, that was one I had lying around...just used it for scale.
    Post by: GATed73, Jun 2, 2017 in forum: Troubleshooting
  9. GATed73
    Post

    Some issues with the R2?

    and success. I found it under the tabbed bottom of the printer, under the bed. Popped it off and it was just sitting near one of the boards....
    Post by: GATed73, Jun 2, 2017 in forum: Troubleshooting
  10. GATed73
    Post

    Some issues with the R2?

    found this fella under the bed, but no sign of the other pieces. [IMG]
    Post by: GATed73, Jun 2, 2017 in forum: Troubleshooting
  11. GATed73
    Post

    Some issues with the R2?

    makes perfect sense. I'll doublecheck the packaging - don't see how anything could move more than a millimeter in there, that thing was packed tight.
    Post by: GATed73, Jun 2, 2017 in forum: Troubleshooting
  12. GATed73
    Post

    Some issues with the R2?

    Here's the picture. [IMG]
    Post by: GATed73, Jun 2, 2017 in forum: Troubleshooting
  13. GATed73
    Post

    Some issues with the R2?

    so i need 3 posts to add a link...picture coming up.
    Post by: GATed73, Jun 2, 2017 in forum: Troubleshooting
  14. GATed73
    Post

    Some issues with the R2?

    I don't think I have a knurled wheel on the extruder shaft. Just a lone shaft, round on maybe 2/3rd, flat on the other 1/3.
    Post by: GATed73, Jun 2, 2017 in forum: Troubleshooting