1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by gunsmoke132

  1. gunsmoke132
    Post

    Partially Solved E motor not working

    the driver is A4988?
    Post by: gunsmoke132, Aug 13, 2019 in forum: Troubleshooting
  2. gunsmoke132
    Post

    Partially Solved E motor not working

    im going to swap e for z because the Z is known to work and the E is in question UPDATE: im 99% sure its the driver... the z is not functioning...
    Post by: gunsmoke132, Aug 13, 2019 in forum: Troubleshooting
  3. gunsmoke132
    Post

    Partially Solved E motor not working

    im going to plug the driver into a different axis to see if i figure out the issue
    Post by: gunsmoke132, Aug 13, 2019 in forum: Troubleshooting
  4. gunsmoke132
    Post

    Partially Solved E motor not working

    true. time to give it more juice lol
    Post by: gunsmoke132, Aug 13, 2019 in forum: Troubleshooting
  5. gunsmoke132
    Post

    Partially Solved E motor not working

    https://imgur.com/gallery/V5Nwn3X its a new wire. i got it to work before. the ramps is brand new. unless something is weird with the new driver...
    Post by: gunsmoke132, Aug 13, 2019 in forum: Troubleshooting
  6. gunsmoke132
    Post

    Partially Solved E motor not working

    Update! I got it moving again! But I’m back at square one because it’s doing this again... https://imgur.com/gallery/V5Nwn3X Most of the noise is...
    Post by: gunsmoke132, Aug 13, 2019 in forum: Troubleshooting
  7. gunsmoke132
    Post

    Partially Solved E motor not working

    ok so i got the motor to work for a short period after retarting the software but now its back to being dead. ive noticed whatever the old motor...
    Post by: gunsmoke132, Aug 13, 2019 in forum: Troubleshooting
  8. gunsmoke132
    Post

    Partially Solved E motor not working

    so i got an update after fiddling with it for a couple of hours at 2 am. it seems almost like it was both the cable and the card because after i...
    Post by: gunsmoke132, Aug 13, 2019 in forum: Troubleshooting
  9. gunsmoke132
    Thread

    Partially Solved E motor not working

    i started printing something only to hear my extruder motor making a horrible grinding noise. natturaly i thought the hotend was clogged and fixed...
    Thread by: gunsmoke132, Aug 12, 2019, 17 replies, in forum: Troubleshooting
  10. gunsmoke132
    Post

    Solved Hot end heating up when it’s not supposed to

    it was the fet
    Post by: gunsmoke132, Aug 12, 2019 in forum: Troubleshooting
  11. gunsmoke132
    Post

    Solved Hot end heating up when it’s not supposed to

    I took a look at the data sheet and I’m starting to think the same. So I’m just going to solder on the old fets on my new board
    Post by: gunsmoke132, Aug 8, 2019 in forum: Troubleshooting
  12. gunsmoke132
    Thread

    Solved Hot end heating up when it’s not supposed to

    i recently replaced my RAMPS 1.4 because I was having issues with my E stepper not working and jittering while all others were still working. It...
    Thread by: gunsmoke132, Aug 8, 2019, 4 replies, in forum: Troubleshooting
  13. gunsmoke132
    Post

    Unresolved Z axis keeps getting out of wack during printing.

    thanks! do you know what pitch the lead screw is on the r1+ ? i found out the hard way its not 8*8
    Post by: gunsmoke132, Jun 8, 2019 in forum: Troubleshooting