1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Hanover

  1. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    The good news is that Benchy printed fine. So did the drawer I was trying to print when this whole thing started. I'm going to assume that it...
    Post by: Hanover, Dec 9, 2017 in forum: Troubleshooting
  2. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    It was the new power supply I just got from Amazon. I put the old one back on and it's working fine. Talk about bad luck. :) I'm going to try...
    Post by: Hanover, Dec 9, 2017 in forum: Troubleshooting
  3. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    So I went and got a new 250v 5A fuse from Home depot, put it in, turned on the switch. The lights in the room blinked, I heard a "TSS!" noise and...
    Post by: Hanover, Dec 9, 2017 in forum: Troubleshooting
  4. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    So I finally had time to put the new power supply in, and the printer wouldn't turn on. The green LED didn't light up in the power supply. So I...
    Post by: Hanover, Dec 7, 2017 in forum: Troubleshooting
  5. Hanover
    Post

    PEI Print Bed Problem

    I've sent them an email already. *crickets*
    Post by: Hanover, Dec 4, 2017 in forum: Troubleshooting
  6. Hanover
    Post

    PEI Print Bed Problem

    You'd think the early adopters would have first dibs on any upgrades. Instead, I get to look at Amazon's web site and see where they are selling...
    Post by: Hanover, Dec 1, 2017 in forum: Troubleshooting
  7. Hanover
    Post

    PEI Print Bed Problem

    I sanded mine as well and it seems to be working okay. I think Im just going to get some 8x8 buildtak and use that next time it's time to replace...
    Post by: Hanover, Nov 29, 2017 in forum: Troubleshooting
  8. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    No, it still shut itself down. I tried printing Benchy just to see...and it also shut itself down during that print. I'm convinced that I have a...
    Post by: Hanover, Nov 27, 2017 in forum: Troubleshooting
  9. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    I think Wheres Waldo gets the bag of Haribo. I opened it up again, very carefully as to not disconnect the fan. I flipped on the power and the...
    Post by: Hanover, Nov 27, 2017 in forum: Troubleshooting
  10. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    Yes, the whole things turns off except for my RepRap display. If I just leave it, it slowly comes back on again. I have some stuff I need to get...
    Post by: Hanover, Nov 26, 2017 in forum: Troubleshooting
  11. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    I guess I needed to stress that the whole printer shuts off. It's just doesn't stop printing. I think the Temperature Fall error is because of...
    Post by: Hanover, Nov 26, 2017 in forum: Troubleshooting
  12. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    I think this is my issue: [MEDIA] He even mentioned that the Arduino was crashing whenever making large prints that cover a lot of area.
    Post by: Hanover, Nov 25, 2017 in forum: Troubleshooting
  13. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    Well, it still shut itself down. Just no error message this time. No log. It ALWAYS happens at the same point in the print though. So Every...
    Post by: Hanover, Nov 25, 2017 in forum: Troubleshooting
  14. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    Yep, that's what I commented out. Unless something reverted before I compiled it. I'll try it again for the sake of sanity. I'll change the...
    Post by: Hanover, Nov 25, 2017 in forum: Troubleshooting
  15. Hanover
    Post

    Solved Robo R1+ Keeps Shutting itself down

    Well...I spoke too soon. It stopped again, even with the new thermistor. Still getting the stupid error about the temperature falling too much....
    Post by: Hanover, Nov 25, 2017 in forum: Troubleshooting