1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Henradrie

  1. Henradrie
    Post

    Solved Inconsistent extrusion R1

    That was too much work compared to doubling up the elastic. Problem solved, at least until the elastic gives out. Not a fix I would recommend, but...
    Post by: Henradrie, Feb 2, 2021 in forum: Troubleshooting
  2. Henradrie
    Post

    Solved Inconsistent extrusion R1

    The printer came with 1 screw so I removed it and put the bands on. It also came with parts in a bag. Maybe I'll have something in my stock of...
    Post by: Henradrie, Feb 1, 2021 in forum: Troubleshooting
  3. Henradrie
    Post

    Solved Inconsistent extrusion R1

    Here are the pictures. [IMG][IMG][IMG] Tube is 2cm long. Sent from my SM-A705W using Tapatalk
    Post by: Henradrie, Jan 31, 2021 in forum: Troubleshooting
  4. Henradrie
    Post

    Solved Inconsistent extrusion R1

    I'm out of town at the moment but will get pictures when I can. In the meantime here is some more information that might be helpful. Consider this...
    Post by: Henradrie, Jan 31, 2021 in forum: Troubleshooting
  5. Henradrie
    Thread

    Solved Inconsistent extrusion R1

    I've been working on getting an R1 working. The latest problem I can't solve is inconsistent extrusion. My parts come out looking this. The...
    Thread by: Henradrie, Jan 30, 2021, 8 replies, in forum: Troubleshooting
  6. Henradrie
    Thread

    Unanswered Could custom shaft aligner contribute to z-banding?

    I have an original R1 and it has z banding issues. Through this forum I've discovered that this is a common problem and am going to be replacing...
    Thread by: Henradrie, Jan 16, 2021, 2 replies, in forum: Troubleshooting
  7. Henradrie
    Post

    Answered Ive got a major z axis problem

    I used this code instead. G28 ; G29 ; G92 E0 ; G01 Z0.10 ; Adjust this to deal with first layer nozzle height G92 Z0 ;
    Post by: Henradrie, Jan 15, 2021 in forum: Troubleshooting
  8. Henradrie
    Post

    Unresolved Potential heat break issues

    Thanks for the suggestions. I started reading into nozzle seasoning and saw how divisive it is. Got cold feet. One article I read mentioned that...
    Post by: Henradrie, Oct 4, 2020 in forum: Troubleshooting
  9. Henradrie
    Post

    Solved Z axis improperly homing

    I had something similar happen to my R1. Issue was that the vertical rods were not straight and this caused one of the limit switches to be open...
    Post by: Henradrie, Sep 23, 2020 in forum: Troubleshooting
  10. Henradrie
    Thread

    Unresolved Potential heat break issues

    I've been printing on my R1+ for a while then the quality degraded. As seen in the picture the first couple layers go down nicely then the next...
    Thread by: Henradrie, Sep 23, 2020, 4 replies, in forum: Troubleshooting
  11. Henradrie
    Post

    Unanswered X axis only moving in one direction

    Just tried that, no change. Even tried that with the extruder chip and nothing changed. I swapped the X and Y axis driver chips and swapped the...
    Post by: Henradrie, Jun 3, 2020 in forum: Troubleshooting
  12. Henradrie
    Post

    Unanswered X axis only moving in one direction

    I have a Robo R1 beta (5/16 leadscrews) that can only move the X-axis one direction. It was working fine then just started exhibiting that...
    Post by: Henradrie, Jun 2, 2020 in forum: Troubleshooting