1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by hey8you

  1. hey8you
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Upgraded my hotend to the E3D v6. Still tweaking the settings in Simplify3D but its working well so far. Just an FYI, they are shipping with a...
    Post by: hey8you, Apr 23, 2018 in forum: Mods and Upgrades
  2. hey8you
    Post

    Solved Z axis moves but makes noise +video

    Its alive! First test print will be a cover for the LCD screen. Thanks for your help guys. [IMG]
    Post by: hey8you, Jan 30, 2018 in forum: Troubleshooting
  3. hey8you
    Post

    Solved Z axis moves but makes noise +video

    Its probably ok then. I had to remove the bed and put it back in the printer several times while I was making the adjustments. Seems a bit higher...
    Post by: hey8you, Jan 23, 2018 in forum: Troubleshooting
  4. hey8you
    Post

    Solved Z axis moves but makes noise +video

    We have a winner! LOL. I adjusted the driver for Z axis and now it works, no buzzing, It moves smoothly. Now only other issue is the heated bed...
    Post by: hey8you, Jan 23, 2018 in forum: Troubleshooting
  5. hey8you
    Post

    Solved Z axis moves but makes noise +video

    I checked the jumpers and they are installed. I even swapped the ones from the old ramps board(just the z axis). All drivers are facing the...
    Post by: hey8you, Jan 22, 2018 in forum: Troubleshooting
  6. hey8you
    Post

    Solved Burnt wires under print bed

    Using Geof's guide I installed the new ramps board. It went smoothly however I now have a new issue. I posted the link below....
    Post by: hey8you, Jan 22, 2018 in forum: General Questions
  7. hey8you
    Thread

    Solved Z axis moves but makes noise +video

    I replaced my old ramps board after the heater bed wires shorted out and now my Z axis is making noise. All other axis will move normally but when...
    Thread by: hey8you, Jan 22, 2018, 9 replies, in forum: Troubleshooting
  8. hey8you
    Post

    Solved Burnt wires under print bed

    Thanks guys. I never heard back from support and so I just ordered from WheresWaldo link. I was hoping for a plug and play solution but this will...
    Post by: hey8you, Jan 16, 2018 in forum: General Questions
  9. hey8you
    Post

    Solved Burnt wires under print bed

    Something like this?...
    Post by: hey8you, Jan 8, 2018 in forum: General Questions
  10. hey8you
    Post

    Solved Burnt wires under print bed

    Thanks Geof. I just got off the phone with customer service and he said they may not sell the replacement for the original R1. He is going to...
    Post by: hey8you, Jan 8, 2018 in forum: General Questions
  11. hey8you
    Post

    Solved Burnt wires under print bed

    Well, I guess i'm an idiot. I should have taken apart my printer first before ordering anything. I took the bottom cover off so I can see how the...
    Post by: hey8you, Jan 8, 2018 in forum: General Questions
  12. hey8you
    Post

    Solved Burnt wires under print bed

    Someone from Robo3D got back to me. They don't sell it separately so I ended up getting a new print bed. I still going to keep the one from amazon...
    Post by: hey8you, Jan 6, 2018 in forum: General Questions
  13. hey8you
    Post

    Solved Burnt wires under print bed

    I ended up buying the one from the link you provided. With the amount of printing I do, I think I can get away with the 150w one. Thanks for your...
    Post by: hey8you, Jan 2, 2018 in forum: General Questions
  14. hey8you
    Post

    Solved Burnt wires under print bed

    I sent them an e-mail yesterday to see if they have one or not. Does the heater also have the temp sensor in it or do I pull the one off mine and...
    Post by: hey8you, Dec 29, 2017 in forum: General Questions