1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by JakeMoore

  1. JakeMoore
    Post

    Solved R1+ Shutting off

    Thank you all so much! With your help, I was able to get my printer running last night and completed a 4 hours print as a test! It ran...
    Post by: JakeMoore, Apr 22, 2019 in forum: Troubleshooting
  2. JakeMoore
    Post

    Solved R1+ Shutting off

    I followed this guide for updating the firmware: https://help.robo3d.com/hc/en-us/articles/115000717071-Updating-firmware-with-Arduino And got a...
    Post by: JakeMoore, Apr 21, 2019 in forum: Troubleshooting
  3. JakeMoore
    Post

    Solved R1+ Shutting off

    I did not. I did keep the stock arduino when I put in the new board.
    Post by: JakeMoore, Apr 21, 2019 in forum: Troubleshooting
  4. JakeMoore
    Post

    Solved R1+ Shutting off

    Thank you! I had to move my end stops, and that guide showed me how to connect the fans and LEDs into the green power plug. Do I need to put any...
    Post by: JakeMoore, Apr 21, 2019 in forum: Troubleshooting
  5. JakeMoore
    Post

    Solved R1+ Shutting off

    Okay, since the power supply is working fine now, I decided to hook up the new board. The only problem is that the new board is a little bit...
    Post by: JakeMoore, Apr 21, 2019 in forum: Troubleshooting
  6. JakeMoore
    Post

    Solved R1+ Shutting off

    I'll be honest, I don't think I was using the voltmeter properly the first time around. Here's a new reading. Is this correct? [img]
    Post by: JakeMoore, Apr 2, 2019 in forum: Troubleshooting
  7. JakeMoore
    Post

    Solved R1+ Shutting off

    Ah, because of the way you said "you can almost see it" I assumed you meant some other component. My mistake! I'll give that sucker a twist when I...
    Post by: JakeMoore, Mar 27, 2019 in forum: Troubleshooting
  8. JakeMoore
    Post

    Solved R1+ Shutting off

    Okay, I measured the output with a voltmeter and it was a puny 20v. So I tried looking for the potentiometer and couldn't seem to find it. So I...
    Post by: JakeMoore, Mar 27, 2019 in forum: Troubleshooting
  9. JakeMoore
    Post

    Solved R1+ Shutting off

    Thanks, I'll take a look after work. I'm assuming clockwise == higher, counter-clockwise == lower?
    Post by: JakeMoore, Mar 19, 2019 in forum: Troubleshooting
  10. JakeMoore
    Post

    Solved R1+ Shutting off

    Do you have a visual aid for that? haha
    Post by: JakeMoore, Mar 19, 2019 in forum: Troubleshooting
  11. JakeMoore
    Post

    Solved R1+ Shutting off

    Sorry, what exactly do you mean by this? My power supply has a switch to go from 110v to 120v. Not sure what you mean by "set screw". I'll grab a...
    Post by: JakeMoore, Mar 19, 2019 in forum: Troubleshooting
  12. JakeMoore
    Post

    Solved R1+ Shutting off

    lol, what I meant was the photo on amazon has a sticker that reads "115v" while my actual unit has one that reads "110v". I've ordered the...
    Post by: JakeMoore, Mar 18, 2019 in forum: Troubleshooting
  13. JakeMoore
    Post

    Solved R1+ Shutting off

    This is the power supply that I put in, set to 110v. (I don't know why the photo on amazon says 115v)....
    Post by: JakeMoore, Mar 17, 2019 in forum: Troubleshooting
  14. JakeMoore
    Post

    Solved R1+ Shutting off

    Update: I replaced all the ramps and did a test print. It still shut off during the bed leveling while heating the extruder. I then unscrewed the...
    Post by: JakeMoore, Mar 17, 2019 in forum: Troubleshooting
  15. JakeMoore
    Post

    Solved R1+ Shutting off

    Yes, it's an R1+. I'm sure. I've replaced a couple of the RAMPS before, so I'm not afraid to dig up in there. I pulled out each one and inspected...
    Post by: JakeMoore, Mar 10, 2019 in forum: Troubleshooting