1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by jonebersole

  1. jonebersole
    Post

    OLD ROBO filament NEW R2

    I made my own. Feel free to use it if you wish. I created an end that i could use with a piece of 3/4" Outer Diameter /1/2" Inner Diameter...
    Post by: jonebersole, Dec 9, 2017 in forum: Troubleshooting
  2. jonebersole
    Post

    Pillowing on top of print on my R2

    Good news... increasing the fill from 'light' to 'dense' when using the recommended settings in Cura for Robo completely resolved the issue of...
    Post by: jonebersole, Dec 9, 2017 in forum: Troubleshooting
  3. jonebersole
    Thread

    Filament Types, Properties, Uses and Print Specs

    I was doing a bit of research on filament types for some of my projects. I came across the link below and I thought I would share. I hope it...
    Thread by: jonebersole, Dec 8, 2017, 2 replies, in forum: Filament
  4. jonebersole
    Post

    Ninjaflex

    I also want to print in flexible materials with my R2. Has anyone had good success with printing from the R2 with a rubberish/flexible material?...
    Post by: jonebersole, Dec 7, 2017 in forum: Filament
  5. jonebersole
    Post

    Pillowing on top of print on my R2

    Here is a close-up of the end that has the issue. It pillows on the end, but as you can see, as it goes up the shaft it doesn't pillow, because it...
    Post by: jonebersole, Dec 5, 2017 in forum: Troubleshooting
  6. jonebersole
    Post

    Pillowing on top of print on my R2

    Shell wall and top/bottom thickness default to 1mm, which is what it is set to.
    Post by: jonebersole, Dec 4, 2017 in forum: Troubleshooting
  7. jonebersole
    Thread

    Pillowing on top of print on my R2

    I'm using Cura for Robo and running the recommended (non-custom) PLA settings for my prints. I'm selecting the light fill. I'm noticing Pillowing...
    Thread by: jonebersole, Dec 4, 2017, 9 replies, in forum: Troubleshooting
  8. jonebersole
    Post

    How to reduce Z Ribbing?

    FDM should work for my immediate needs, but future projects may dictate having a completely smooth surface on the edges. I'll still work toward...
    Post by: jonebersole, Nov 29, 2017 in forum: Troubleshooting
  9. jonebersole
    Post

    How to reduce Z Ribbing?

    Ok, thanks for the info. I'll try to adjust the Z offset a bit and see what the results are. That first link you provided looks like a great...
    Post by: jonebersole, Nov 29, 2017 in forum: Troubleshooting
  10. jonebersole
    Post

    Cura won't install R2 printer on HP Laptop

    Is the software installed, but just not working, or is it not installing for some reason? Can you provide error messages? You may need to install...
    Post by: jonebersole, Nov 28, 2017 in forum: Troubleshooting
  11. jonebersole
    Post

    How to reduce Z Ribbing?

    My terminology may be off Mark, but it is the z height edges that are created when the layers are printed (squished together). I thought this was...
    Post by: jonebersole, Nov 28, 2017 in forum: Troubleshooting
  12. jonebersole
    Thread

    How to reduce Z Ribbing?

    I've owned a Robo R1+ for many years now. It served my needs well, but i recently bought an R2 as an upgrade. Although the hotend was pushed out...
    Thread by: jonebersole, Nov 28, 2017, 15 replies, in forum: Troubleshooting