1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by jscottb

  1. jscottb
    Post

    Test your printers clearance and tolerance by Maker's Muse

    It's been since 2017 since I tried to print items like this on my R2, but they never would break free do to over extrusion. I have it tuned quite...
    Post by: jscottb, Feb 26, 2020 in forum: Show and Tell
  2. jscottb
    Post

    Quiet fan recomendations for the R2

    Yeah, I have those on my Tevo Tornado now for part cooling.
    Post by: jscottb, Feb 21, 2020 in forum: General Questions
  3. jscottb
    Post

    Quiet fan recomendations for the R2

    Yeah, I saw that it was hard-wired poking around a little at it. I have 24v fans on my other two printers. I will do some research. Thanks.
    Post by: jscottb, Feb 21, 2020 in forum: General Questions
  4. jscottb
    Thread

    Quiet fan recomendations for the R2

    I really would like to replace the fans, especially the 20mm hotend cooler fan. It howls like the wind in an old horror movie. I have other...
    Thread by: jscottb, Feb 21, 2020, 5 replies, in forum: General Questions
  5. jscottb
    Post

    Print Stuck

    After the bed cools, I typically keep a box cutter razor blade (just the rectangular blade) and gently work it under one side if round or a corner...
    Post by: jscottb, Feb 21, 2020 in forum: Troubleshooting
  6. jscottb
    Post

    Micro Porous Glass Bed Install

    I see. For that, I would just get glass then and use glue stick or hair spray. I used to use Rave on my Rep-Rap years ago. Rave was what my...
    Post by: jscottb, Feb 10, 2020 in forum: Mods and Upgrades
  7. jscottb
    Post

    Micro Porous Glass Bed Install

    I have been using the Anycubic glass for about year and a half with great success. I have the 214x214 I think but the 220x220 will fit. I use...
    Post by: jscottb, Feb 10, 2020 in forum: Mods and Upgrades
  8. jscottb
    Post

    Printer error Bed not heating up

    You can still print pla without the heat. I have been printing with mine. Just turn off the heated bed in your slicer profiles and the startup...
    Post by: jscottb, Nov 20, 2017 in forum: Troubleshooting
  9. jscottb
    Post

    Printer error Bed not heating up

    I just ordered one. They say they are on back-order. :(
    Post by: jscottb, Nov 19, 2017 in forum: Troubleshooting
  10. jscottb
    Post

    What print speed are you printing at most of the time?

    Nice. I may experiment more.
    Post by: jscottb, Nov 15, 2017 in forum: General Questions
  11. jscottb
    Post

    3D Printed Birds' Nest....

    If you can figure out what layer it was or close to, try chopping the part up to print from that point and see what it does. I know thats not what...
    Post by: jscottb, Nov 15, 2017 in forum: Troubleshooting
  12. jscottb
    Post

    3D Printed Birds' Nest....

    *Some* of it looks like there was a clog, but usually not quite that much. Heat creep maybe? What the extrude and he like after? Do you see a lot...
    Post by: jscottb, Nov 15, 2017 in forum: Troubleshooting
  13. jscottb
    Thread

    What print speed are you printing at most of the time?

    This is for plain ole PLA and medium quality prints. I have printed as fast as 68mm a sec and the temp at 206c with goodish results. Most of the...
    Thread by: jscottb, Nov 14, 2017, 6 replies, in forum: General Questions