1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Lance Weston

  1. Lance Weston
    Post

    Fan voltages?

    All fans 12v
    Post by: Lance Weston, Oct 16, 2025 in forum: General Questions
  2. Lance Weston
    Post

    question on auto leveling

    That confirms it. It has been working. I have two identical machines with creality glass beds. I fully clean the beds then spray a coat of...
    Post by: Lance Weston, Aug 7, 2025 in forum: Software
  3. Lance Weston
    Thread

    question on auto leveling

    Is M420 L1 the way to load the mesh Is M420 S1 the way to activate mesh leveling does the following gcode script make sense with initial mesh set...
    Thread by: Lance Weston, Aug 2, 2025, 4 replies, in forum: Software
  4. Lance Weston
    Post

    Need Factory Image for RoboOS (Robo R2)

    I must have posted this at least 6 times. Look around and if you can't find it i will dig it up and post again
    Post by: Lance Weston, Feb 25, 2025 in forum: Software
  5. Lance Weston
    Post

    G36 Failure

    Check the cable to to the ir board
    Post by: Lance Weston, Dec 7, 2024 in forum: Troubleshooting
  6. Lance Weston
    Post

    Fan voltages?

    Robo R2 uses all 12v fans except for the system fan in the basement which is 24v
    Post by: Lance Weston, Nov 9, 2024 in forum: General Questions
  7. Lance Weston
    Post

    What to do when the extruder stepper gags

    I am printing up some non critical mechanical parts that take about half an hour each. I got the dreaded stepper missing steps and gagging. I...
    Post by: Lance Weston, Oct 19, 2024 in forum: Troubleshooting
  8. Lance Weston
    Post

    What to do when the extruder stepper gags

    I have changed all of my steppers from 1.8 degree to 0.9 degree. this has resulted in quieter operation but did not give me the quality...
    Post by: Lance Weston, Oct 12, 2024 in forum: Troubleshooting
  9. Lance Weston
    Post

    What to do when the extruder stepper gags

    First thing I did was to replace the 42mm stepper with a 48mm stepper. I then adjusted the current.
    Post by: Lance Weston, Sep 22, 2024 in forum: Troubleshooting
  10. Lance Weston
    Post

    What to do when the extruder stepper gags

    I am making up some non critical parts. I have been using old PLA of various manufactures just to get rid of it. I use the Partsbuilt system...
    Post by: Lance Weston, Sep 13, 2024 in forum: Troubleshooting
  11. Lance Weston
    Post

    Bearing size/part number

    Use the specialty class not the cheap ones you find everywhere. Not so much for the quality of print, it does make a very slight difference, but...
    Post by: Lance Weston, Sep 13, 2024 in forum: Troubleshooting
  12. Lance Weston
    Thread

    What to do when the extruder stepper gags

    I began to print a larger object. The extruder would start to skip steps at so time into the print. I found as the temp went up it failed...
    Thread by: Lance Weston, Aug 8, 2024, 8 replies, in forum: Troubleshooting
  13. Lance Weston
    Post

    Layer shifting Y-Axis

    Get yourself a 3mm button head screw set. Button head for clearance. Where the block has separated drill a hole in both corners of the block....
    Post by: Lance Weston, Jul 29, 2024 in forum: Troubleshooting