1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Lasse Knudsen

  1. Lasse Knudsen
    Thread

    Partial Answer Filament hard to push through extruder

    Greetings, I have several robo3D printers, however one of them has an issue with "normal" PLA, in that it will always gnaw into it so it cannot...
    Thread by: Lasse Knudsen, Feb 12, 2018, 2 replies, in forum: Troubleshooting
  2. Lasse Knudsen
    Post

    Solved Weird behavior from extruder stepper motor

    Brilliant Mark! :) I had an old motor driver lying around from a kick starter Robo and now it works. Thank you for taking time to help me solve...
    Post by: Lasse Knudsen, Dec 19, 2016 in forum: Troubleshooting
  3. Lasse Knudsen
    Thread

    Solved Weird behavior from extruder stepper motor

    Greetings, I have some trouble with the extruder stepper on my printer, it has begun behaving oddly. It looks like its being asked to step, but...
    Thread by: Lasse Knudsen, Dec 19, 2016, 2 replies, in forum: Troubleshooting
  4. Lasse Knudsen
    Post

    Solved Z axis "long hex nuts" showing

    Thank you Mark, i managed to get the printer going with new screws, and with out glue :)
    Post by: Lasse Knudsen, Dec 9, 2016 in forum: Troubleshooting
  5. Lasse Knudsen
    Post

    Solved Z axis "long hex nuts" showing

    It was harder that anticipated, as the screwhead was stripped, and after assembly i realized that i had not tighted them enough to they went loose...
    Post by: Lasse Knudsen, Dec 8, 2016 in forum: Troubleshooting
  6. Lasse Knudsen
    Thread

    Solved Z axis "long hex nuts" showing

    Greetings, i had a print that was righer than i realized, and now the two brass hex nuts are showing, and zstop no longer works. How do i go...
    Thread by: Lasse Knudsen, Dec 7, 2016, 4 replies, in forum: Troubleshooting
  7. Lasse Knudsen
    Post

    Solved Problems with "Pitting" in top layers

    the part is 2mm thick and the infill my friend uses is around 20, he was not specific
    Post by: Lasse Knudsen, Oct 21, 2016 in forum: Troubleshooting
  8. Lasse Knudsen
    Post

    Solved Problems with "Pitting" in top layers

    Greetings, i just tried with the gcode that my coworker used, and its close enough to perfect, we are looking at 0.1 layer height and 5 top...
    Post by: Lasse Knudsen, Oct 21, 2016 in forum: Troubleshooting
  9. Lasse Knudsen
    Thread

    Solved Problems with "Pitting" in top layers

    Greetings, i see issues with pitting when i print with few top layers, the picture shows a print printed at 0.1 mm layer height, 25% infill, With...
    Thread by: Lasse Knudsen, Oct 20, 2016, 9 replies, in forum: Troubleshooting
  10. Lasse Knudsen
    Thread

    Unresolved Robo3D Layer issue while printing.

    Greetings, I did two things to improve the situation, first one was really silly on my part. turned out that the heated bed was touching the wall,...
    Thread by: Lasse Knudsen, Aug 23, 2016, 1 replies, in forum: Troubleshooting