1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by mamejay

  1. mamejay
    Post

    BLTouch bracket and some sort of guide

    OK. I have started looking at it myself and connecting the BLTouch looks fairly straightforward. For the firmware I will be using the TH3D marlin...
    Post by: mamejay, Jun 5, 2020 in forum: Mods and Upgrades
  2. mamejay
    Thread

    BLTouch bracket and some sort of guide

    Hey team, My Robo3D has been neglected and left to gather dust. I have 2 Ender3's now running th3d firmware and BLTouch and I have never looked...
    Thread by: mamejay, Jun 5, 2020, 2 replies, in forum: Mods and Upgrades
  3. mamejay
    Post

    Answered Z Access not smooth. Replaced bearing but same issue

    I have everything in as tight as it can go. One thing I found is that when I cut the cable tie for the belt the carriage could flow up and down...
    Post by: mamejay, Nov 3, 2019 in forum: Troubleshooting
  4. mamejay
    Thread

    Answered Z Access not smooth. Replaced bearing but same issue

    Hey everyone, My Z carriage is playing up and getting stuck during G28 and causing the Z switches to engage and think the nozzle had touched the...
    Thread by: mamejay, Nov 2, 2019, 4 replies, in forum: Troubleshooting
  5. mamejay
    Post

    Setting Z Offset Marlin 1.1.9

    Thanks for that one. Will compile and get it uploaded to my printer shortly. I am actually looking at 2.0 now so may just get that installed and...
    Post by: mamejay, Oct 28, 2019 in forum: Mods and Upgrades
  6. mamejay
    Post

    Setting Z Offset Marlin 1.1.9

    Here you go. I enabled eeprom support as this was commented out. https://www.dropbox.com/s/bk5xdbh0lgtdeiq/Marlin%201.1.9.zip?dl=0
    Post by: mamejay, Oct 27, 2019 in forum: Mods and Upgrades
  7. mamejay
    Thread

    Setting Z Offset Marlin 1.1.9

    Hey Team, I upgraded to Marlin 1.1.9 using Novice Experts build from his Youtube video. I am trying to get the Z Offset set by printing a large...
    Thread by: mamejay, Oct 26, 2019, 5 replies, in forum: Mods and Upgrades
  8. mamejay
    Post

    Answered Replacement Extruder Stepper Motor R1

    I grabbed this stepper but a little confused about what connections go to what pins. Attached is a picture of my current cable and diagram of the...
    Post by: mamejay, Oct 21, 2019 in forum: Troubleshooting
  9. mamejay
    Post

    Answered Replacement Extruder Stepper Motor R1

    Superstar. thanks for that. I have a replacement on the way. Just need to work out the wiring.
    Post by: mamejay, Oct 15, 2019 in forum: Troubleshooting
  10. mamejay
    Thread

    Answered Replacement Extruder Stepper Motor R1

    Hey Guys, My extruder stepper is slipping. Its has markings of 42HS40-1704JA (1066mm) I cannot find the JA type on 42HS40-1704A Which replacement...
    Thread by: mamejay, Oct 15, 2019, 5 replies, in forum: Troubleshooting
  11. mamejay
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Thanks for that. They just look exactly the same as what I got and have the same specs on them. Is there a difference with the r1plus and r1...
    Post by: mamejay, Dec 5, 2017 in forum: Mods and Upgrades