1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Miguel Angel Quintero

  1. Miguel Angel Quintero
    Post

    Solved Up is down and down is down

    Thanks guys...looks like it was the pololu boards/switches whatever they're called....I switched it out and that did the trick...thanks again...
    Post by: Miguel Angel Quintero, Dec 14, 2016 in forum: Troubleshooting
  2. Miguel Angel Quintero
    Post

    Solved Up is down and down is down

    I agree...but I haven't touched the wires...I did an arduino reset by pushing the reset button, but now it stops printing at layer 4 or 5 and...
    Post by: Miguel Angel Quintero, Dec 12, 2016 in forum: Troubleshooting
  3. Miguel Angel Quintero
    Thread

    Solved Up is down and down is down

    Hi...I'm sure there is an easy explanation for why my z axis is going down when I send it up...I've seen this problem before but I can't remember...
    Thread by: Miguel Angel Quintero, Dec 11, 2016, 4 replies, in forum: Troubleshooting
  4. Miguel Angel Quintero
    Post

    Solved retraction problems

    Hey @danzca6 and @Geof, I fixed the problem...I simply reset the artuino physically and uploaded the firmware. Danzca, I just hit update usually,...
    Post by: Miguel Angel Quintero, Sep 14, 2016 in forum: Troubleshooting
  5. Miguel Angel Quintero
    Post

    Solved retraction problems

    I'm almost certain it's the AVR board updater from the firmware...I just installed a different version and now the retraction digs in instead of...
    Post by: Miguel Angel Quintero, Sep 13, 2016 in forum: Troubleshooting
  6. Miguel Angel Quintero
    Post

    Solved retraction problems

    ah...yes...it's always been 2560...
    Post by: Miguel Angel Quintero, Sep 13, 2016 in forum: Troubleshooting
  7. Miguel Angel Quintero
    Post

    Solved retraction problems

    here's my m503...
    Post by: Miguel Angel Quintero, Sep 13, 2016 in forum: Troubleshooting
  8. Miguel Angel Quintero
    Post

    Solved retraction problems

    I just measured the rods...they are neither 8mm or 5/16...they are about 7.4mm...
    Post by: Miguel Angel Quintero, Sep 13, 2016 in forum: Troubleshooting
  9. Miguel Angel Quintero
    Post

    Solved retraction problems

    I have the original rods that came with the r1 from 2014...I'm not sure what rods they are???
    Post by: Miguel Angel Quintero, Sep 13, 2016 in forum: Troubleshooting
  10. Miguel Angel Quintero
    Post

    Solved retraction problems

    I have the R1 and I use the ROBO3DR1V3 firmware I'm somewhat savvy with this thing and I can't figure out what is going on????
    Post by: Miguel Angel Quintero, Sep 13, 2016 in forum: Troubleshooting
  11. Miguel Angel Quintero
    Post

    Solved retraction problems

    It's definitely not coming back down on the z after a retraction in certain parts...the robo prints perfectly up until retraction comes into...
    Post by: Miguel Angel Quintero, Sep 13, 2016 in forum: Troubleshooting
  12. Miguel Angel Quintero
    Post

    Solved retraction problems

    hi...thank you for taking a look...here is the pic..
    Post by: Miguel Angel Quintero, Sep 13, 2016 in forum: Troubleshooting
  13. Miguel Angel Quintero
    Thread

    Solved retraction problems

    I appreciate all that have suggestions... I'll lead with: I started noticing the issue when I updated the AVR board in Arduino. but even going...
    Thread by: Miguel Angel Quintero, Sep 13, 2016, 16 replies, in forum: Troubleshooting