1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Miguel Rodriguez

  1. Miguel Rodriguez
    Post

    IR Board/Partsbuilt buildtak material

    I may take you up on that offer in the near future. After the last message I went on a search of the 0available materials and build surfaces on...
    Post by: Miguel Rodriguez, Mar 5, 2022 in forum: Troubleshooting
  2. Miguel Rodriguez
    Post

    IR Board/Partsbuilt buildtak material

    I guess the question then is why do they sell it? Does anyone have suggestions on what would work? I do not have the magnetic bed.
    Post by: Miguel Rodriguez, Feb 21, 2022 in forum: Troubleshooting
  3. Miguel Rodriguez
    Thread

    IR Board/Partsbuilt buildtak material

    So i have not seen anything on this but i may have not hit the right set of search terms so I am sorry if I missed it. So I got one of the Robo...
    Thread by: Miguel Rodriguez, Feb 21, 2022, 11 replies, in forum: Troubleshooting
  4. Miguel Rodriguez
    Post

    Unresolved Print looks like sandpaper

    My generic ramps R1+ has had all the components aside from motors and power supply replaced. Honestly the only things that have not been replaced...
    Post by: Miguel Rodriguez, Oct 24, 2020 in forum: Troubleshooting
  5. Miguel Rodriguez
    Post

    Unresolved Print looks like sandpaper

    Sorry for taking so long to respond, been a rough week at wok. So I replaced pretty much all of the parts on my robo r1+ and still have no idea...
    Post by: Miguel Rodriguez, Oct 24, 2020 in forum: Troubleshooting
  6. Miguel Rodriguez
    Post

    Unresolved Print looks like sandpaper

    I tried it but now it just sounds super loud when extruder goes down from any height, i think i did it right. Anyway I know what the issue is...
    Post by: Miguel Rodriguez, Oct 19, 2020 in forum: Troubleshooting
  7. Miguel Rodriguez
    Post

    Unresolved Print looks like sandpaper

    Ok, so this is new to me. The link showed me how to boost the current and I understand that but it does not say what the max limit for the motors...
    Post by: Miguel Rodriguez, Oct 17, 2020 in forum: Troubleshooting
  8. Miguel Rodriguez
    Post

    Unresolved Print looks like sandpaper

    Here you go.
    Post by: Miguel Rodriguez, Oct 17, 2020 in forum: Troubleshooting
  9. Miguel Rodriguez
    Post

    Unresolved Print looks like sandpaper

    Sorry about that, I keep forgetting that there is an R1 and an R1+. I have the R1+ and used ROBO3DR1PLUSV2 firmware. Also, I did not let the...
    Post by: Miguel Rodriguez, Oct 17, 2020 in forum: Troubleshooting
  10. Miguel Rodriguez
    Post

    Unresolved Print looks like sandpaper

    I recently rebuilt from the frame up a Robo R1 and the firmware i got was from the Robo site so I believe it to be the stock firmware with some...
    Post by: Miguel Rodriguez, Oct 17, 2020 in forum: Troubleshooting
  11. Miguel Rodriguez
    Post

    Unresolved Print looks like sandpaper

    Sorry, accidentally deleted my post. I recently did a tune up on my Robo R1+ and replaced the belts. tightened them, replaced the hotend nozzle,...
    Post by: Miguel Rodriguez, Oct 16, 2020 in forum: Troubleshooting
  12. Miguel Rodriguez
    Thread

    Unresolved Print looks like sandpaper

    Print issue https://imgur.com/a/37iDD53
    Thread by: Miguel Rodriguez, Oct 16, 2020, 18 replies, in forum: Troubleshooting
  13. Miguel Rodriguez
    Post

    Solved Robo C2 - Stops Printing Mid Print then Freezes

    So I figured out what the issue is and I feel silly, especially because I am a computer tech. My nic card on my desktop was going out and was...
    Post by: Miguel Rodriguez, Aug 5, 2020 in forum: Troubleshooting