1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by NateTheApe

  1. NateTheApe
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Ha! Yes that sounds much more precise than me guessing...well whipped out the calipers and the first layer looks awesome!
    Post by: NateTheApe, Oct 13, 2016 in forum: Mods and Upgrades
  2. NateTheApe
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    @WheresWaldo PERFECT! Thanks, I was thinking that a Z-Offset of -1.00 should have put the nozzle in the bed :P I'll run the G29 command when I get...
    Post by: NateTheApe, Oct 13, 2016 in forum: Mods and Upgrades
  3. NateTheApe
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Does Z-Offset work or do you have to use the G29 S4 Zn.nn command to adjust Z with MESH? I set the Z-Offset on the LCD but I don't see much...
    Post by: NateTheApe, Oct 13, 2016 in forum: Mods and Upgrades
  4. NateTheApe
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I ran into this same issue with the V6, at first I just tuned my fans down to 75% to resolve it. Then I installed the silicon sock from E3D and I...
    Post by: NateTheApe, Oct 11, 2016 in forum: Mods and Upgrades
  5. NateTheApe
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    So after fighting with MESH leveling, then realizing that ABL wasn't acting right for awhile...It turns out you were right @WheresWaldo; The left...
    Post by: NateTheApe, Oct 11, 2016 in forum: Mods and Upgrades
  6. NateTheApe
    Post

    KTMDirtFace's new R1+

    Yes the Hatchbox red is very nice now, they must have changed the formula. The first roll I ordered a while back was very orange but the roll I...
    Post by: NateTheApe, Aug 31, 2016 in forum: Show and Tell
  7. NateTheApe
    Post

    NateTheApe's Robo R1 Upgraded

    Yes, I know...but my R1 will do just fine in the mean time. As for the leadscrews those will probably be done after vacation in Oct, from what...
    Post by: NateTheApe, Aug 31, 2016 in forum: Show and Tell
  8. NateTheApe
    Thread

    NateTheApe's Robo R1 Upgraded

    I've had my R1 for a little over a year now, and since about this time last year the printer has ran 24/7. Finally this past month I started...
    Thread by: NateTheApe, Aug 31, 2016, 2 replies, in forum: Show and Tell
  9. NateTheApe
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Thanks @WheresWaldo I happened to be home for lunch and took a second look at it. I'm thinking that I will need to have the left and right holders...
    Post by: NateTheApe, Aug 29, 2016 in forum: Mods and Upgrades
  10. NateTheApe
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Yes, I happened to try a "Store Memory" on the LCD and a M500 to store it. I also verified that it showed me all of the points by doing a G29.
    Post by: NateTheApe, Aug 29, 2016 in forum: Mods and Upgrades
  11. NateTheApe
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Finished the Titan/E3DV6 install this weekend and tried out both firmwares. For some reason I was just having hell with ABL and had never tried...
    Post by: NateTheApe, Aug 29, 2016 in forum: Mods and Upgrades
  12. NateTheApe
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Finally decided to make the switch to a E3D V6 after a year and a half of using the hexagon, so since I'm uploading new firmware I'll give this a...
    Post by: NateTheApe, Aug 24, 2016 in forum: Mods and Upgrades
  13. NateTheApe
    Post

    Unanswered Quieter fans for the R1

    Perfect! This is what I was looking for as well. Although I've dealt with the noise for over a year, I've decided to switch to all Noctua's in the...
    Post by: NateTheApe, Mar 10, 2016 in forum: General Questions