1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Omar Basha

  1. Omar Basha
    Post

    IR board fix

    Cool, thanks for that. My machine is currently stripped down, my nephew is putting it back together, am experimenting with vesconite bearings I...
    Post by: Omar Basha, Jan 16, 2022 in forum: Mods and Upgrades
  2. Omar Basha
    Post

    IR board fix

    Hi, Would this fix the nozzle crashing into bed issue some of us have? Sent from my SM-N970F using Tapatalk
    Post by: Omar Basha, Jan 16, 2022 in forum: Mods and Upgrades
  3. Omar Basha
    Post

    R2 E3D V6 or any other popular hotend

    Hi, Couldn't find the post, below is from the mail I sent for my order, so to have 5 sets thats what I ordered, 2 pins per connector. 10 x...
    Post by: Omar Basha, Jul 12, 2021 in forum: Mods and Upgrades
  4. Omar Basha
    Post

    R2 E3D V6 or any other popular hotend

    Hi, its quite simple, just remove the original hot end by loosening the collar bolt, and than swop over heater and thermistor to v6 block and fit...
    Post by: Omar Basha, Jul 12, 2021 in forum: Mods and Upgrades
  5. Omar Basha
    Post

    Trying to resurrect my R2

    Lol... great minds, I was thinking of doing something similiar, since there's nothing special about the robos core design it shouldn't be too much...
    Post by: Omar Basha, Jul 6, 2021 in forum: Mods and Upgrades
  6. Omar Basha
    Post

    Thank you guys !

    Well done, please share the specifics of your upgrade. Sent from my SM-N970F using Tapatalk
    Post by: Omar Basha, Sep 26, 2020 in forum: Mods and Upgrades
  7. Omar Basha
    Thread

    Vesconite Bearings

    Hi guys, as per Lance's request, just going to share an alternative bearing I found for my Robo R2. I haven't fitted it yet, still need to get new...
    Thread by: Omar Basha, Jul 15, 2020, 0 replies, in forum: Mods and Upgrades
  8. Omar Basha
    Post

    My R2 Carriage upgrade

    Thanks for that, will let you know soon. Lol I'm in South Africa so essentially will have to goto the same shop where I got the fake hot end for...
    Post by: Omar Basha, Jul 15, 2020 in forum: Mods and Upgrades
  9. Omar Basha
    Post

    My R2 Carriage upgrade

    Well done, especially on the bearings. My rods are scored from the lousy ones that with the machine, I had vesconite bearings made up for both the...
    Post by: Omar Basha, Jul 15, 2020 in forum: Mods and Upgrades
  10. Omar Basha
    Post

    moving backwards. need to start over.

    When we had screen issues, I removed the ribbon and cleaned the all the contacts on the screen and ribbon with alcohol and it solved it. Our issue...
    Post by: Omar Basha, Apr 12, 2020 in forum: Troubleshooting
  11. Omar Basha
    Post

    Replacing The Hotend with E3D

    @mark, Lol I figured that out retrospectively. Only one shop in South Africa keeps the original and they are literally a 1000 miles away on the...
    Post by: Omar Basha, Dec 9, 2019 in forum: Mods and Upgrades
  12. Omar Basha
    Post

    Replacing The Hotend with E3D

    Hi All, just throwing my 5c in. I printed the above mentioned shroud, was no-where near big enough for the e3d I got. I did a simpler solution......
    Post by: Omar Basha, Dec 9, 2019 in forum: Mods and Upgrades
  13. Omar Basha
    Thread

    Raspberry Pi and display dead

    Hi, Just thought we'd share our current experience. Our machines screen went dead and on further inspection the pi was dead. Tested with a spare...
    Thread by: Omar Basha, Jul 17, 2019, 2 replies, in forum: Troubleshooting