1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by sebrobin

  1. sebrobin
    Post

    Community Favorite Alternative to the Lead Screw Upgrade Kit

    thank you
    Post by: sebrobin, Jan 28, 2017 in forum: Mods and Upgrades
  2. sebrobin
    Post

    Community Favorite Alternative to the Lead Screw Upgrade Kit

    Hi, I'm about to perform this change. Do you need to upload the metric firmware or only change this value even if you have the imperial firmware...
    Post by: sebrobin, Jan 28, 2017 in forum: Mods and Upgrades
  3. sebrobin
    Post

    Solved Stop extruding with new extruder

    I think it stops to extrude after 20 sec because the filament is bent because it comes from the reel. I straight the first centimetre to insert...
    Post by: sebrobin, Oct 4, 2016 in forum: Troubleshooting
  4. sebrobin
    Post

    Solved Stop extruding with new extruder

    I have ordered a E3DV6. thank you all for your help
    Post by: sebrobin, Oct 4, 2016 in forum: Troubleshooting
  5. sebrobin
    Post

    Solved Stop extruding with new extruder

    http://community.robo3d.com/index.php?threads/e3d-v6-information-installation-guides-and-review.3407/ Mike Kelly explains very well my issue in...
    Post by: sebrobin, Oct 4, 2016 in forum: Troubleshooting
  6. sebrobin
    Post

    Solved Stop extruding with new extruder

    the E3DV6 cost 43£ where the hexagon is 39$. This is quite the same.
    Post by: sebrobin, Oct 4, 2016 in forum: Troubleshooting
  7. sebrobin
    Post

    Solved Stop extruding with new extruder

    I have Robo3D filament but they are quite old. I have one unopened but it is ABS. I'll take my calliper and advise the diameter. What hotend do...
    Post by: sebrobin, Oct 4, 2016 in forum: Troubleshooting
  8. sebrobin
    Post

    Solved Stop extruding with new extruder

    I have disassembled the hotend and the filament is very tight in it ! What is the point of having it so tight ?? I am a bit fed up by the poor...
    Post by: sebrobin, Oct 4, 2016 in forum: Troubleshooting
  9. sebrobin
    Post

    Solved Stop extruding with new extruder

    I have a beta. Black hotend
    Post by: sebrobin, Oct 4, 2016 in forum: Troubleshooting
  10. sebrobin
    Post

    Solved Stop extruding with new extruder

    I also think it is too cold. Do you know if the firmware must be modified when you change the hotend ? (from the original hotend to the Hexagonal...
    Post by: sebrobin, Oct 4, 2016 in forum: Troubleshooting
  11. sebrobin
    Thread

    Solved Stop extruding with new extruder

    I had to replace the original extruder with the Hexagon Hotend (purchased at Robo3D). It extrudes fine but after 20 seconds, it stops extruding....
    Thread by: sebrobin, Oct 4, 2016, 21 replies, in forum: Troubleshooting
  12. sebrobin
    Post

    Answered What kind of connector does the R1 and R1 +plus extruder use?

    I have ordered a new Hexagon hotend, and the cables of the thermistor seems thinner than the one for the heater (seems obvious). Can someone thell...
    Post by: sebrobin, Sep 5, 2016 in forum: General Questions
  13. sebrobin
    Post

    Unresolved Crap result... Please Help !

    thanks Mark, I'll try that. Anything on my config that you find odd ?
    Post by: sebrobin, Aug 31, 2016 in forum: Troubleshooting
  14. sebrobin
    Post

    Unresolved Crap result... Please Help !

    never done anything on the nozzle. how do you clean it ?
    Post by: sebrobin, Aug 31, 2016 in forum: Troubleshooting