1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by SeeingBlue

  1. SeeingBlue
    Post

    Bought bltouch & mini ir, no luck yet...

    That did it. Thank you, man.
    Post by: SeeingBlue, Nov 6, 2021 in forum: Mods and Upgrades
  2. SeeingBlue
    Post

    Bought bltouch & mini ir, no luck yet...

    I used the same video. Watched it again just to make sure. The only difference is I'm not using servo 0 as he did. I haven't even gotten to the...
    Post by: SeeingBlue, Nov 6, 2021 in forum: Mods and Upgrades
  3. SeeingBlue
    Post

    Bought bltouch & mini ir, no luck yet...

    Thank you for that. I plugged the bltouch back up. Black and white plug on z endstop pins. White to the outside, black matches the same...
    Post by: SeeingBlue, Nov 6, 2021 in forum: Mods and Upgrades
  4. SeeingBlue
    Post

    Bought bltouch & mini ir, no luck yet...

    It is the R1+, but black shield? The shell is white, the plate is black glass, the ramps board is black. The middle block that mounts the plate...
    Post by: SeeingBlue, Nov 6, 2021 in forum: Mods and Upgrades
  5. SeeingBlue
    Post

    Bought bltouch & mini ir, no luck yet...

    Thanks, RoboRage. The light does come on. It will even self-test at boot. What it would not do is push out the pin on z homing or follow any other...
    Post by: SeeingBlue, Nov 6, 2021 in forum: Mods and Upgrades
  6. SeeingBlue
    Thread

    Bought bltouch & mini ir, no luck yet...

    I have bought both the blTouch and Mini IR and have not managed to get either one working. I'll tell you what I've done so far and where I am at...
    Thread by: SeeingBlue, Nov 5, 2021, 12 replies, in forum: Mods and Upgrades
  7. SeeingBlue
    Post

    Unanswered Z-Axis Alignment issues

    I dont know what's wrong with it. I checked everything I could see, not very experienced at what I'm look at though. I leveled everything with a...
    Post by: SeeingBlue, Jan 6, 2018 in forum: Troubleshooting
  8. SeeingBlue
    Post

    Unanswered Z-Axis Alignment issues

    Alright so I'm still investigating but do you think the Y or horizontal rail might not be straight? When I removed the case I noticed that the...
    Post by: SeeingBlue, Jan 5, 2018 in forum: Troubleshooting
  9. SeeingBlue
    Post

    Unanswered Z-Axis Alignment issues

    I do know that in the brackets do appear even on the brass nut. They are not flush with the bottom of the nut, but about quarter to half inch from...
    Post by: SeeingBlue, Jan 5, 2018 in forum: Troubleshooting
  10. SeeingBlue
    Post

    Unanswered Z-Axis Alignment issues

    Yea, I've been using a business card to gauge the distance. I didn't do that today though, I just eyeballed it for the video. I did play with the...
    Post by: SeeingBlue, Jan 5, 2018 in forum: Troubleshooting
  11. SeeingBlue
    Post

    Unanswered Z-Axis Alignment issues

    It's almost like it's dragging or I'm not aligning the z axis properly? But I don't know how that's possible if the nozzle moves across the bed...
    Post by: SeeingBlue, Jan 5, 2018 in forum: Troubleshooting
  12. SeeingBlue
    Post

    Unanswered Z-Axis Alignment issues

    Prior to the video I lowered the nozzle with the lead screws until both end-stops clicked, then I further adjusted them until the nozzle moved...
    Post by: SeeingBlue, Jan 5, 2018 in forum: Troubleshooting
  13. SeeingBlue
    Post

    Unanswered Z-Axis Alignment issues

    I go to lunch in 10 minutes. I'll capture a video then. Thanks guys.
    Post by: SeeingBlue, Jan 5, 2018 in forum: Troubleshooting
  14. SeeingBlue
    Post

    Unanswered Z-Axis Alignment issues

    If it didn't turn then it wouldn't move at all right? The left side couldn't force the rod to turn on the right. It moves as far as that goes.
    Post by: SeeingBlue, Jan 5, 2018 in forum: Troubleshooting