1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Shane

  1. Shane
    Post

    Full Graphic Controller Screen

    I just did a test print and the start to flash again after the print finishes. This time its not with ? but the XYZ just flashes.
    Post by: Shane, May 21, 2017 in forum: Mods and Upgrades
  2. Shane
    Post

    Full Graphic Controller Screen

    yes I do. That makes sense seeing how it only flash while the printer is at idle before a print. once I start my print and everything homes it...
    Post by: Shane, May 21, 2017 in forum: Mods and Upgrades
  3. Shane
    Post

    Full Graphic Controller Screen

    Thanks you for the help but even moving that number up to 10 had no effect. If it helps the XYZ is flashing ? Not the position numbers.
    Post by: Shane, May 21, 2017 in forum: Mods and Upgrades
  4. Shane
    Thread

    Full Graphic Controller Screen

    K so need some help with this one. Sense I updated my firmware to 1.1.1 my screen shows my normal XYZ position but then flashes over and shows a...
    Thread by: Shane, May 20, 2017, 5 replies, in forum: Mods and Upgrades
  5. Shane
    Post

    PSU M80/M81 issues

    Its weird even with an older version/ stock my commands are backwards. It has to be something with my ramps board itself? I will get with Marlin...
    Post by: Shane, May 20, 2017 in forum: Mods and Upgrades
  6. Shane
    Post

    PSU M80/M81 issues

    Thanks for the inputs. Im not trying to turn off the arduino just the power supply.
    Post by: Shane, May 20, 2017 in forum: Mods and Upgrades
  7. Shane
    Thread

    PSU M80/M81 issues

    Hey everyone, So I finally got my SSR installed for control of my psu but im having a strange issue. My M80 will turn my psu off and m81 will...
    Thread by: Shane, May 19, 2017, 5 replies, in forum: Mods and Upgrades
  8. Shane
    Post

    Answered S3D auto level issues

    No I have everything offset wise in S3D at 0. I think adding the M565 Z-1.0 helped. It is still lower then I would like but it seams like it just...
    Post by: Shane, Apr 23, 2017 in forum: Troubleshooting
  9. Shane
    Post

    Answered S3D auto level issues

    No I didn't know that, what would I use to wipe my nozzle for any oozing before the print starts.
    Post by: Shane, Apr 23, 2017 in forum: Troubleshooting
  10. Shane
    Post

    Answered S3D auto level issues

    G28 ; home all axes G29 ; probe the bed G1 Z5 F5000 ; lift nozzle G28 ; home all axes G1 Z5 F5000 ; lift nozzle M109 S[extruder0_temperature]...
    Post by: Shane, Apr 23, 2017 in forum: Troubleshooting
  11. Shane
    Post

    Answered S3D auto level issues

    no that's my issue it is still printing to close to the bed which jams the nozzle causing my filament to strip sometimes. If it does print even...
    Post by: Shane, Apr 23, 2017 in forum: Troubleshooting
  12. Shane
    Post

    Answered S3D auto level issues

    ok so I did all that then when I homed all the last line shows z-0.90. Then here is another auto level. SENT: M502 READ: echo:Hardcoded Default...
    Post by: Shane, Apr 23, 2017 in forum: Troubleshooting
  13. Shane
    Post

    Answered S3D auto level issues

    Do you think that is where this Z number is coming from, the Flash eprom? READ: X:0.00 Y:0.00 Z:-0.80 E:0.00 Count X: 0.00 Y:0.00 Z:-0.80 So if I...
    Post by: Shane, Apr 23, 2017 in forum: Troubleshooting