1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by TheGlutton

  1. TheGlutton
    Post

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    @WheresWaldo sorry for the mixup! I edited my post above to say that all of the example photos in that post were a .2mm printed at 50mm/s speed....
    Post by: TheGlutton, Jul 31, 2016 in forum: Troubleshooting
  2. TheGlutton
    Post

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    Time for an update. Made big strides, but still having some issues. I used the Paper Leveling method and found that the right side of the...
    Post by: TheGlutton, Jul 31, 2016 in forum: Troubleshooting
  3. TheGlutton
    Post

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    @Geof Thank you for the offer, I may take you up on it in the future :)
    Post by: TheGlutton, Jul 28, 2016 in forum: Troubleshooting
  4. TheGlutton
    Post

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    @Ryan TeGantvoort Thank you, I have just updated the XY_Jerk to 12, and the acceleration settings to {600, 600, 100, 10000}, added a belt...
    Post by: TheGlutton, Jul 28, 2016 in forum: Troubleshooting
  5. TheGlutton
    Post

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    I just finished a 5hr 20min Benchy, and it looks a little better, but MAN was that painfully slow... @mark tomlinson Speed definitely kills, but...
    Post by: TheGlutton, Jul 28, 2016 in forum: Troubleshooting
  6. TheGlutton
    Thread

    Unresolved 3d Systems Cube3 Quality > My ROBO R1

    Hey Everyone! I just want to start by saying thank you to all those who helped get me up and running through my last thread! :D Ok so I think I...
    Thread by: TheGlutton, Jul 28, 2016, 14 replies, in forum: Troubleshooting
  7. TheGlutton
    Post

    Solved New Printer Issues

    The control board is now running cool and my test cube is 20cm high :D The print quality is also imensly improved, I am going camping this weekend...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  8. TheGlutton
    Post

    Solved Prints Short on Z axis

    Can confirm, my control board fan was not wired correctly and my 20cm calibration cubes were consistently coming out at 17mm high with terrible...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  9. TheGlutton
    Post

    Solved New Printer Issues

    @danzca6 Thank you! You are spot on, I think that I have the z-axis issue fixed (with my control board fan now actually running) after this cube...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  10. TheGlutton
    Post

    Solved New Printer Issues

    OK, I used these settings for PLA: http://wiki.eccmakers.com/index.php?title=Robo3d_Settings_for_Cura And was able to get the quality to improve...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  11. TheGlutton
    Post

    Solved New Printer Issues

    Latest test cube still almost exactly 17mm, or 3mm to short... I am at a complete loss, in addition to being short the print quality is quite...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  12. TheGlutton
    Post

    Solved New Printer Issues

    OK, I have modified my Gcode by adding the lines from this thread by @Ben R:...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  13. TheGlutton
    Post

    Solved New Printer Issues

    I have tried: -Powercycling the printer -setting z-offset to .9 -setting z-offset to 0 -setting z offset to -1 -z-offset 1.0 -Printing with...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting
  14. TheGlutton
    Post

    Solved New Printer Issues

    Re-flashing the firmware did not fix the printing to close to the bed issue, i re ran M503: > M503 < echo:Steps per unit: < echo: M92 X80.00...
    Post by: TheGlutton, Jul 22, 2016 in forum: Troubleshooting