1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by TRAVIS KEMP

  1. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Also, Do you know if an inductive sensor can be used on my glass bed, if my platform is a solid sheet of aluminum? Glass is 3-4mm thick, is this...
    Post by: TRAVIS KEMP, Dec 12, 2016 in forum: Mods and Upgrades
  2. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Alright thanks, I'll do that. The IR, pretty straight forward? I'd like something simple to implement. Basically just looking for something...
    Post by: TRAVIS KEMP, Dec 12, 2016 in forum: Mods and Upgrades
  3. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    So, I was wondering if anyone on here using MESH, is using a sensor of some sort (BLTouch, Prox. Switch) to run the mesh probes? I have a much...
    Post by: TRAVIS KEMP, Dec 12, 2016 in forum: Mods and Upgrades
  4. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I usually do fairly precise stuff. So I like this way, more or less how I have been doing it, u just gave me some better tips. I ended up with...
    Post by: TRAVIS KEMP, Nov 21, 2016 in forum: Mods and Upgrades
  5. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    so i have noticed that with the lcd, no matter what i do, i cant get it to go in .01 increments, like either 224 or 226 deg, and either -.01 or...
    Post by: TRAVIS KEMP, Nov 21, 2016 in forum: Mods and Upgrades
  6. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Got ya, so really, they made that the width, damn. So then thats what I need to adjust to make the first layer "full" and stick. That was pretty...
    Post by: TRAVIS KEMP, Nov 21, 2016 in forum: Mods and Upgrades
  7. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Ideally shouldn't offset be the thickness of what you use to mesh as a negative? I thought s3d first layer would raise the model above 100 but...
    Post by: TRAVIS KEMP, Nov 21, 2016 in forum: Mods and Upgrades
  8. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    So you set your z offset the same as your layer height? And maybe I don't understand how s3d first layer extrusion percentage works? It seems that...
    Post by: TRAVIS KEMP, Nov 21, 2016 in forum: Mods and Upgrades
  9. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Are your firmware settings correct for end stops?
    Post by: TRAVIS KEMP, Nov 21, 2016 in forum: Mods and Upgrades
  10. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Then you should be right on at .24-.25 make it S4 Z-0.11 Also I usually still put this in my start code because I have slightly different offsets...
    Post by: TRAVIS KEMP, Nov 20, 2016 in forum: Mods and Upgrades
  11. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    @ProfessorPinky Need that number to be a negative to go lower
    Post by: TRAVIS KEMP, Nov 20, 2016 in forum: Mods and Upgrades
  12. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Ya I know, I've been doing mesh from s3d but it only steps down at .1mm at the lowest, wanted it more accurate and the ability to babystep if...
    Post by: TRAVIS KEMP, Nov 20, 2016 in forum: Mods and Upgrades
  13. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Got ya that's cool, I'll do that, btw the headers are on correctly, works fine now that I turned off the kill pin. Not really that big a deal, I...
    Post by: TRAVIS KEMP, Nov 20, 2016 in forum: Mods and Upgrades
  14. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Yes I did try it with stock firmware last night, with the sainsmart board. Still the same thing. I agree I'm pretty sure there are some...
    Post by: TRAVIS KEMP, Nov 20, 2016 in forum: Mods and Upgrades
  15. TRAVIS KEMP
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I would normally agree with anything you say, but the only thing with that, is with the ribbon cables unplugged from the adapter, meaning LCD not...
    Post by: TRAVIS KEMP, Nov 20, 2016 in forum: Mods and Upgrades