1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by woferry

  1. woferry
    Post

    Modding Questions (E3d and other)

    E3D also left the tubing out of my v6 order, I emailed them and they sent me the missing piece. I didn't have as much time between ordering and...
    Post by: woferry, Apr 20, 2017 in forum: General Questions
  2. woferry
    Post

    E3D Titan Extruder

    So has anybody thought about the Titan Aero yet? I never opted for the Titan, but the reduced Z footprint looks really tempting to me. I'd...
    Post by: woferry, Apr 3, 2017 in forum: Mods and Upgrades
  3. woferry
    Post

    Unresolved E3D v6 Torubleshooting

    Since you appear to be printing the E3D quick-release plate, are you still using the original one with the E3D hotend? The mount on the v6...
    Post by: woferry, May 9, 2016 in forum: Troubleshooting
  4. woferry
    Post

    Web enabled Robo3d using Raspberry Pi and Octoprint

    I never use the printer/LCD's SD Card (I don't even have a card installed), I suspect that's why you'd be seeing the slowness, as the pipe between...
    Post by: woferry, Apr 18, 2016 in forum: Mods and Upgrades
  5. woferry
    Post

    E3D v6 Information, Installation Guides, and Review

    I also wasn't interested in running wiring all the way back to the RAMPS board and had the right JST connectors on-hand, so I wired up the E3D's...
    Post by: woferry, Apr 18, 2016 in forum: Mods and Upgrades
  6. woferry
    Post

    Have I missed any modifications to my Robo R1+?

    Curious, are there any of these surfaces that can withstand the heated nozzle? I find with the filaments I'm using that I get some drooling from...
    Post by: woferry, Apr 5, 2016 in forum: Show and Tell
  7. woferry
    Post

    Unanswered AutoLevel command moving bed too far (grinding)

    That must really vary from printer to printer. The heated portion of my R1+Plus's bed is reasonably well-centered within the white box, but the...
    Post by: woferry, Mar 14, 2016 in forum: Troubleshooting
  8. woferry
    Post

    Unanswered Hot end now spinning - Have I broken it?

    Ah, didn't catch that you were talking about the fan, you said fan mount but I was thinking about the retaining bracket. Depending on your Robo...
    Post by: woferry, Mar 7, 2016 in forum: Troubleshooting
  9. woferry
    Post

    Unanswered Robo Calibration for tight part fitment!

    I use Cura (15.04.4), could never get MatterControl 1.4 to even launch without crashing and wasn't that happy with Slic3r 1.2.9 when I tried it...
    Post by: woferry, Mar 7, 2016 in forum: Troubleshooting
  10. woferry
    Post

    Unanswered Hot end now spinning - Have I broken it?

    FYI, I was able to move from the Hexagon to an E3D even though I hadn't printed the thicker bracket yet (I didn't even realize that was required...
    Post by: woferry, Mar 7, 2016 in forum: Troubleshooting
  11. woferry
    Post

    somemore stupid questions

    The problem is that the old filament won't "run out". As soon as it's past the end of the hobbed-bolt what's left (like 2-3" of filament) will...
    Post by: woferry, Mar 4, 2016 in forum: General Questions
  12. woferry
    Post

    Hello From San Jose CA

    Hi from another San Jose resident! "Like scan" might be scad? OpenSCAD is free, but you do need to be comfortable with doing all of your...
    Post by: woferry, Mar 4, 2016 in forum: United States of America
  13. woferry
    Post

    Web enabled Robo3d using Raspberry Pi and Octoprint

    1) I started out with the totally stock firmware as shipped with my R1+Plus (I've since re-flashed to enable the full graphics LCD and set my...
    Post by: woferry, Mar 3, 2016 in forum: Mods and Upgrades
  14. woferry
    Post

    Solved Extruder Motor Stops

    The G29 command is what does the leveling, if you take that out it won't happen. Make sure you fully power-cycle the Robo, i.e. remove USB and...
    Post by: woferry, Mar 2, 2016 in forum: Troubleshooting
  15. woferry
    Post

    Solved Extruder Motor Stops

    I don't think that should be the case. It certainly isn't true for my R1+plus. When the extruder is leveling on the left my left switch...
    Post by: woferry, Mar 1, 2016 in forum: Troubleshooting