1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by WZ9V

  1. WZ9V
    Post

    what material would you use?

    Heated nozzle will melt BuildTak when probing. I would suggest probing with nozzle cold and experiment to find the difference when heated (not...
    Post by: WZ9V, Dec 12, 2016 in forum: General Questions
  2. WZ9V
    Post

    Time for Aluminum bed.

    I run a 360W 120V heater on the stock power supply and a DC/AC SSR. A 360W heater gets to 110C in three minutes and I'm using 6mm glass.
    Post by: WZ9V, Sep 13, 2016 in forum: Mods and Upgrades
  3. WZ9V
    Post

    Time for Aluminum bed.

    I got my from a place on AliExpress which works fine but I recently bought a Keenovo one and it seems better built but less flexible. Since we...
    Post by: WZ9V, Sep 7, 2016 in forum: Mods and Upgrades
  4. WZ9V
    Post

    Time for Aluminum bed.

    The general consensus (RepRap forums) is that a heated bed should use cast aluminum tooling plate. That is very flat and stays flat as heated....
    Post by: WZ9V, Sep 5, 2016 in forum: Mods and Upgrades
  5. WZ9V
    Post

    Duet Wifi controller board

    I have one of those I picked up along the way as a trade, have not tried it and it kind of seems like the whole effort is dying off. I was hoping...
    Post by: WZ9V, Aug 31, 2016 in forum: Mods and Upgrades
  6. WZ9V
    Post

    KTMDirtFace's new R1+

    No painting here. I just like to get a decent color filament to start. But I'm usually just make parts for other things/machines .
    Post by: WZ9V, Aug 31, 2016 in forum: Show and Tell
  7. WZ9V
    Post

    Duet Wifi controller board

    I think I'm in batch 3. Mine will probably end up in my Delta rebuild.
    Post by: WZ9V, Aug 31, 2016 in forum: Mods and Upgrades
  8. WZ9V
    Post

    Duet Wifi controller board

    I have a pre-order one on the way because I like the wireless capability. I've been resisting a second one which I know I will end up buying...
    Post by: WZ9V, Aug 31, 2016 in forum: Mods and Upgrades
  9. WZ9V
    Post

    Duet Wifi controller board

    I'm not an expert but I did have a 0.8.5 version running for a while. His Delta calibration is great assuming your Delta is not possessed like...
    Post by: WZ9V, Aug 31, 2016 in forum: Mods and Upgrades
  10. WZ9V
    Post

    Duet Wifi controller board

    Try the web interface first before you decide on the LCD. You might find it unnecessary if you have a tablet since you can monitor everything via...
    Post by: WZ9V, Aug 30, 2016 in forum: Mods and Upgrades
  11. WZ9V
    Post

    Duet Wifi controller board

    I have a Duet 0.8.5 I used in a Delta. Nice board and David supports it well. Very different from the Marlin firmware though. It uses G-Code...
    Post by: WZ9V, Aug 30, 2016 in forum: Mods and Upgrades
  12. WZ9V
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I've found it only has to be close to level, but you do need to be close or it does not work well. My biggest gripe now that I have some time and...
    Post by: WZ9V, Aug 30, 2016 in forum: Mods and Upgrades
  13. WZ9V
    Post

    KTMDirtFace's new R1+

    Yes, I have not found a nice red yet. Either too orange or too pink.
    Post by: WZ9V, Aug 30, 2016 in forum: Show and Tell
  14. WZ9V
    Post

    KTMDirtFace's new R1+

    I'll keep an eye out for that Red. I really don't like the Magenta one when printed. Looks so much better on the spool. I've always wondered...
    Post by: WZ9V, Aug 29, 2016 in forum: Show and Tell
  15. WZ9V
    Post

    KTMDirtFace's new R1+

    some say the Inland is just rebranded eSun. Transparent pinkish is how mine prints, I was hoping you had more of a redish color. If your using...
    Post by: WZ9V, Aug 29, 2016 in forum: Show and Tell