1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by xfire_dragonx

  1. xfire_dragonx
    Post

    Solved Lift nozzle after G29 start code

    so my start code change would be this? G21 ; set units to metric G28 X0 Y0 Z0 ; home all axis M565 Z-1.0 define Z offset at 1.0mm G29 ; probe...
    Post by: xfire_dragonx, Jan 26, 2023 in forum: General Questions
  2. xfire_dragonx
    Post

    Solved Lift nozzle after G29 start code

    Should the G1 come after G29? Just want nozzle to lift and not drag on print bed.
    Post by: xfire_dragonx, Jan 26, 2023 in forum: General Questions
  3. xfire_dragonx
    Thread

    Solved Lift nozzle after G29 start code

    Heyo, been a while since being here asking a question about my start code - did have my start code setup to have the nozzle lift after the G29 of...
    Thread by: xfire_dragonx, Jan 25, 2023, 5 replies, in forum: General Questions
  4. xfire_dragonx
    Thread

    Solved Start Gcode help

    I'm looking for the gcode that raises the hot end after the last g29 before printing and can't remember the dang code. G28 M565 G1 Z5 F5000...
    Thread by: xfire_dragonx, Jun 30, 2022, 1 replies, in forum: General Questions
  5. xfire_dragonx
    Post

    Partial Answer print not original shape in z axis

    The switches are setup properly[IMG] [ATTACH]
    Post by: xfire_dragonx, Jan 20, 2019 in forum: Troubleshooting
  6. xfire_dragonx
    Post

    Partial Answer print not original shape in z axis

    Have 2 new switches hooked up and still same result. I did a board check and switched Z and X, the result of a M119: Reporting endstop status...
    Post by: xfire_dragonx, Jan 20, 2019 in forum: Troubleshooting
  7. xfire_dragonx
    Post

    Partial Answer print not original shape in z axis

    z_min stays open after sending the G1 Z0
    Post by: xfire_dragonx, Jan 18, 2019 in forum: Troubleshooting
  8. xfire_dragonx
    Post

    Partial Answer print not original shape in z axis

    This is what i get: M119 SENDING:M119 Reporting endstop status x_min: TRIGGERED y_min: TRIGGERED z_min: open the G29 works to a degree, [MEDIA]
    Post by: xfire_dragonx, Jan 18, 2019 in forum: Troubleshooting
  9. xfire_dragonx
    Post

    Partial Answer print not original shape in z axis

    I tested in cura. the x/y home works ( top left corner). z axis does the same thing in cura, used gcode command line in cura. G 28 works on the...
    Post by: xfire_dragonx, Jan 18, 2019 in forum: Troubleshooting
  10. xfire_dragonx
    Post

    Partial Answer print not original shape in z axis

    changed this to #define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true. Printer test: The head goes to the center of the bed...
    Post by: xfire_dragonx, Jan 16, 2019 in forum: Troubleshooting
  11. xfire_dragonx
    Post

    Partial Answer print not original shape in z axis

    // ENDSTOP SETTINGS: // Sets direction of endstops when homing; 1=MAX, -1=MIN #define X_HOME_DIR -1 #define Y_HOME_DIR -1 #define Z_HOME_DIR -1...
    Post by: xfire_dragonx, Jan 14, 2019 in forum: Troubleshooting
  12. xfire_dragonx
    Post

    Partial Answer print not original shape in z axis

    changed both to false: const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.//robo #define...
    Post by: xfire_dragonx, Jan 14, 2019 in forum: Troubleshooting
  13. xfire_dragonx
    Post

    Partial Answer print not original shape in z axis

    the machine homes x/y no problem, when the machine halted at the z axis homing I had the end stops disconnected. The z axis rods do not spin,...
    Post by: xfire_dragonx, Jan 11, 2019 in forum: Troubleshooting