1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by znet3d

  1. znet3d
    Thread

    Unanswered Multi color prints getting back to exact paused location

    So I have been trying out printing with multi color. I am using MC, I pause the printer at a desired layer, move the extruder up about 30mm,...
    Thread by: znet3d, Jun 16, 2016, 3 replies, in forum: General Questions
  2. znet3d
    Post

    Multiple colors with single extruder

    I tried to do this using the MC slicer. worked great the first time I tried it, by simply pausing it moving 30mm up, change filament, move 30mm...
    Post by: znet3d, Jun 15, 2016 in forum: Printing Filament
  3. znet3d
    Post

    Answered Printer went crazy

    What I think happened was that the tie strap at the top that was holding the wires was to tight and got caught when moving. I have replaced it...
    Post by: znet3d, Jun 15, 2016 in forum: Troubleshooting
  4. znet3d
    Post

    Answered Chunks of glass came off with print

    I just wanted to be sure, if I cover the bed with LEXAN, do I then still put the blue tape on the LEXAN or use the glue stick like on the glass bed?
    Post by: znet3d, Jun 15, 2016 in forum: Troubleshooting
  5. znet3d
    Post

    Answered Chunks of glass came off with print

    Thanks for all the advice, ROBO support was great, they are shipping me a replacement bed for a discounted price, I ordered the LEXAN sheet but I...
    Post by: znet3d, Jun 15, 2016 in forum: Troubleshooting
  6. znet3d
    Post

    Answered Chunks of glass came off with print

    So something like this will work? Lexan Sheet - Polycarbonate - .030" - 1/32" Thick, Clear, 12" x 12"...
    Post by: znet3d, Jun 15, 2016 in forum: Troubleshooting
  7. znet3d
    Thread

    Answered Chunks of glass came off with print

    So this morning I go to pull off a printed part of the glass bed, and noticed that chunks of glass just came off stuck to my printed part and now...
    Thread by: znet3d, Jun 14, 2016, 16 replies, in forum: Troubleshooting
  8. znet3d
    Post

    Answered Printer went crazy

    Anything I can do, should be doing to help prevent the switches from getting stuck? Or are there things I can make for the screws so that it stops...
    Post by: znet3d, Apr 19, 2016 in forum: Troubleshooting
  9. znet3d
    Thread

    Answered Printer went crazy

    So, I started printing the Robo3D tool holder from Thingverse: http://www.thingiverse.com/thing:913811 I watched it do the first layer and...
    Thread by: znet3d, Apr 18, 2016, 4 replies, in forum: Troubleshooting
  10. znet3d
    Post

    Solved Bottom layer has gaps

    Hello, I apologies it took me couple of days to tryout some of the suggestions you guys provided. So I used the Macro buttons to play with...
    Post by: znet3d, Apr 7, 2016 in forum: Troubleshooting
  11. znet3d
    Post

    Solved Bottom layer has gaps

    Thank you for all your feedback, I am using the hatchbox filament and will try to lower the temp. The printer bed was nice and clean when I did...
    Post by: znet3d, Apr 4, 2016 in forum: Troubleshooting
  12. znet3d
    Post

    Solved Bottom layer has gaps

    Dear Robo3d community, This is my first 3D printer and I have been learning a lot and I have a lot more to learn, I was hoping someone could help...
    Post by: znet3d, Apr 4, 2016 in forum: Troubleshooting