1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Answered How to readjust the z offset

Discussion in 'Troubleshooting' started by formtechn, May 2, 2017.

  1. formtechn

    formtechn New Member

    Joined:
    Apr 4, 2017
    Messages:
    9
    Likes Received:
    1
    How to readjust the z offset on r1+? I just switch to e3d v6 and the nozzle is close to the plate, which is not allowing the filament to come out smoothly.
     
    #1 formtechn, May 2, 2017
  2. Jeff Meador

    Jeff Meador New Member

    Joined:
    Dec 18, 2016
    Messages:
    22
    Likes Received:
    2
    In your slicer software, you should be able to go under settings and make the adjustment.

    Sent from my VS990 using Tapatalk
     
    #2 Jeff Meador, May 2, 2017
  3. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    In your start up script you should be using a M565 Z-1.0; set the z offset for autolevel

    The -1.0 is what you adjust. -.9 is closer -1.1 is further.
     
    #3 Geof, May 2, 2017
  4. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    for more exact instructions we will need to know what slicer your using and how you adjusted it before.
     
    #4 Geof, May 2, 2017
  5. banolka

    banolka Member

    Joined:
    Jun 20, 2016
    Messages:
    31
    Likes Received:
    5
    I have same problem i use cura 2.3.1 made for robo


    Sent from my iPhone using Tapatalk
     
    #5 banolka, May 4, 2017
  6. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    There is your answer. If you are not using the R1/R1+ then you posted in the wrong place :)
     
    #6 mark tomlinson, May 4, 2017
  7. banolka

    banolka Member

    Joined:
    Jun 20, 2016
    Messages:
    31
    Likes Received:
    5
    I have R1 with E3D v6


    Sent from my iPhone using Tapatalk
     
    #7 banolka, May 4, 2017
  8. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    Edit the startup Script as @Geof suggested.
    should be similar to :
    G28;
    M565 Z-1.0;
    G29;
     
    #8 mark tomlinson, May 4, 2017
  9. David Avila

    David Avila Member

    Joined:
    Mar 16, 2016
    Messages:
    69
    Likes Received:
    5
    how to I check that if I use mattercontrol ?
     
    #9 David Avila, Sep 13, 2017
  10. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    #10 WheresWaldo, Sep 13, 2017

Share This Page