1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Installing a MOSFET

Discussion in 'Mods and Upgrades' started by Curtis Wolfe, May 30, 2017.

  1. Curtis Wolfe

    Curtis Wolfe Active Member

    Joined:
    Feb 21, 2017
    Messages:
    254
    Likes Received:
    78
    I want to install a MOSFET for the heatbed on my Robo R1+

    I've watched a couple videos.

    I just want to make sure I have the wiring correct.

    PSU-MOSFET-RAMPS? or directly to the bed?

    Also do I need to put a fan on the MOSFET?

    This is the MOSFET I ended up getting.

    https://www.amazon.com/gp/product/B06WV7FBCV/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

    There's a +/- for the power in side but not for the output side. It just says heatbed.

    Thanks
     
  2. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    The MOSFET has an input for power and an output for power and another input for control.

    The two labeled hot bed will be the output to the bed heater.
    The +/- DC in goes to 12v Power supply.

    The control input goes to the output of the RAMPS that would normally control the bed heat.

    (line up all of the +/- correctly too)
     
  3. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    Personally I'd opt for a solid state relay instead, but this will work too.
     
  4. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Solid state is the way to go if you want that type of set up/higher current.
     
  5. daniel871

    daniel871 Well-Known Member

    Joined:
    Apr 18, 2015
    Messages:
    1,322
    Likes Received:
    510
  6. Curtis Wolfe

    Curtis Wolfe Active Member

    Joined:
    Feb 21, 2017
    Messages:
    254
    Likes Received:
    78
    I don't see a +/- on the output of the Mosfet.
     
  7. Curtis Wolfe

    Curtis Wolfe Active Member

    Joined:
    Feb 21, 2017
    Messages:
    254
    Likes Received:
    78
    Maybe I do. Do you think that's the positive side?

    [​IMG]
     
  8. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    @Curtis Wolfe the heating element is a pure resistive load, there is no plus or minus. It can be wired any way you like.
     
    Geof and mark tomlinson like this.
  9. Curtis Wolfe

    Curtis Wolfe Active Member

    Joined:
    Feb 21, 2017
    Messages:
    254
    Likes Received:
    78

    That's what I suspected. Thanks
     

Share This Page