1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Solved Z axis height is off

Discussion in 'Troubleshooting' started by Drew Appling, Mar 2, 2015.

Page 3 of 3
  1. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    Esteps are not Z steps or X steps or Y steps, I said that the 723.38 number for the extruder should be closer to 800 - 820 in order to extrude the correct amount of filament when asked.
     
    #41 WheresWaldo, Jun 8, 2017
  2. aznhlfan

    aznhlfan Active Member

    Joined:
    Sep 19, 2015
    Messages:
    383
    Likes Received:
    59
    Correct, so that is when I measured and came up to 950

    Sent from my Galaxy S7 using Tapatalk
     
    #42 aznhlfan, Jun 8, 2017
  3. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    Did you only measure one time? Did you make sure there was plenty of tension on the filament? Take an average of at least three measurements.
     
    #43 WheresWaldo, Jun 8, 2017
  4. aznhlfan

    aznhlfan Active Member

    Joined:
    Sep 19, 2015
    Messages:
    383
    Likes Received:
    59
    Did 2

    Sent from my Galaxy S7 using Tapatalk
     
    #44 aznhlfan, Jun 8, 2017
  5. aznhlfan

    aznhlfan Active Member

    Joined:
    Sep 19, 2015
    Messages:
    383
    Likes Received:
    59
    I will try a 3rd tommorow

    Sent from my Galaxy S7 using Tapatalk
     
    #45 aznhlfan, Jun 8, 2017
  6. emilio sanchez

    emilio sanchez New Member

    Joined:
    Feb 27, 2016
    Messages:
    1
    Likes Received:
    0
    Hello
    I saw this forum and i want to ask for your help, in the eeprom setting i changed 2267 in the steps per mm to 2560 and the printer doesn't work, the motors moves but doesnt reach the home, i maked a test put 2450 in eeprom setting and the printer work, the adjust is better but i need 2560 steps per mm, can you help me?
     
    #46 emilio sanchez, Jul 7, 2017
  7. Darwin Tadena

    Darwin Tadena New Member

    Joined:
    Jul 7, 2020
    Messages:
    1
    Likes Received:
    0



    Hi Mike,
    What is the best setting for EEProm for best result or what is the best setting for robo 3d r1 plus
     
    #47 Darwin Tadena, Jul 7, 2020
  8. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    Mike Kelly was last seen: Apr 21, 2020

    He doesn't come to the forum very often any longer.

    The Z steps/mm as defined in the Marlin configuration.h will be:

    Robo3D beta: 2560
    Robo3D R1: 2267.72
    Robo3D R1+: 800
     
    #48 mark tomlinson, Jul 7, 2020
Page 3 of 3

Share This Page