1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

General issues

Discussion in 'Off Topic' started by Antonio_gt, May 27, 2018.

Thread Status:
Not open for further replies.
  1. Antonio_gt

    Antonio_gt New Member

    Joined:
    May 27, 2018
    Messages:
    3
    Likes Received:
    0
    Hi every one, i have a tronxy X5 from january and a month ago i broke up the thread tube of the hot end and from i replace it i have a lot of issues with my printings i cannot print again as good as before.
    I use cura and when its start to print the first movement that it does is put down the hotbed and rise it while the extruder is going into the printing position (it doesnt do this before)
    Anothe problem is that if i set the origin in the center in cura the printer start in one corner and not in the center and sometimes neither start in the center of the bed.
    The first layer is a mess because it doest constant with the flow and the acuracy of the pieces is not 100% axact
    What i can do?
    I tried a lot of configurstions and saw a lot of tuturials


    Enviado desde mi iPhone utilizando Tapatalk
     
  2. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    Not sure how much help you will be able to get here on your Tronxy, this forum is specific to Robo3D printers. The Tronxy is not one of those.
     
  3. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    What firmware are you using?
    I know Marlin is available for the Tronxy... not sure what it comes with.
     
  4. Antonio_gt

    Antonio_gt New Member

    Joined:
    May 27, 2018
    Messages:
    3
    Likes Received:
    0
    The firmware default is Marlin 1.1.5 and i tried to upload the latest version but i had a problem to load the sketch into the board, i stalled sanguino and set the atmega1284 microcontroller at 16mhz but i dont know why the arduino ide doesnt load the sketch into the board
    Thanks for your reply!
     
  5. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    Paste in the errors here that you are getting and we can try to help.
     
  6. Antonio_gt

    Antonio_gt New Member

    Joined:
    May 27, 2018
    Messages:
    3
    Likes Received:
    0
    CC27B8E1-B8B7-49C1-A3DF-20F7F58D50CF.png 28BEF975-44F1-49E8-8BE9-2F44ECD88C3E.png 9144F55C-C8C2-4F0C-9E06-7174188F0DDD.png
    I followed this post and the instructions writen on it and thats the result
     
  7. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    That error implies that the arduino IDE is not able to lock the serial port it wants to use to program the board.
     
  8. huh77

    huh77 New Member

    Joined:
    Jun 25, 2018
    Messages:
    3
    Likes Received:
    0
    hey thanks... I was struggling with similar. :)
     
  9. huh77

    huh77 New Member

    Joined:
    Jun 25, 2018
    Messages:
    3
    Likes Received:
    0
    You really saved me a lot of time :)
     
Thread Status:
Not open for further replies.

Share This Page