1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Unresolved R1 plus hotend clog

Discussion in 'Troubleshooting' started by Chamodh Madusanka, Oct 8, 2015.

  1. Chamodh Madusanka

    Chamodh Madusanka New Member

    Joined:
    Oct 3, 2015
    Messages:
    4
    Likes Received:
    0
    Hii everyone i have a robo3d r1plus printer and now it's clogged. I think nozzle is blocked. Because filament can go through until the nozzle. So how do i unclog the nozzle.
    What is the reason to happen this. I updated my mattercontrol to 1.4 version. After that its got clog. And some how for me mattercontrol works better than cura. The settings i used are default. I used ABS filement from matterhacker for my prints. Thanks

    Sent from my SM-G900FD using Tapatalk
     
    #1 Chamodh Madusanka, Oct 8, 2015
  2. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    #2 mark tomlinson, Oct 9, 2015
  3. Chamodh Madusanka

    Chamodh Madusanka New Member

    Joined:
    Oct 3, 2015
    Messages:
    4
    Likes Received:
    0
    I already clean the clog thanks. Have you try the mattercontrol 1.4 version. It doesn't print only heating up.

    Sent from my SM-G900FD using Tapatalk
     
    #3 Chamodh Madusanka, Oct 9, 2015
  4. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    No, I do not use mattercontrol.
     
    #4 mark tomlinson, Oct 9, 2015
  5. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,276
    Drop out the nozzle by pulling on the quick release tab. Check for any filament sticking out.

    For help with mattercontrol, ask matterhackers directly as we do not troubleshoot that: https://www.matterhackers.com/community/forum
     
    #5 Mike Kelly, Oct 9, 2015
  6. Chamodh Madusanka

    Chamodh Madusanka New Member

    Joined:
    Oct 3, 2015
    Messages:
    4
    Likes Received:
    0
    Oh it's working now thanks

    Sent from my SM-G900FD using Tapatalk
     
    #6 Chamodh Madusanka, Oct 9, 2015
  7. Chuck Erwin

    Chuck Erwin Active Member

    Joined:
    Aug 27, 2015
    Messages:
    202
    Likes Received:
    136
    "Drop out the nozzle by pulling on the quick release tab"

    I just had a PLA jam and I had to unscrew the two Allen screws and drop out the whole thing which is very hard on my fingers.
    What is this quick release thing you talk of? Maybe I missed something or miss understood what you are talking about. I would love a quick release tab!
     
    #7 Chuck Erwin, Oct 9, 2015
  8. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    New R1+ -- it has a different way of attaching the hotend.
     
    #8 mark tomlinson, Oct 10, 2015
  9. Mike Kelly

    Mike Kelly Volunteer

    Joined:
    Mar 11, 2013
    Messages:
    6,967
    Likes Received:
    2,276
    You said you had an R1 plus so I gave instructions based on that
     
    #9 Mike Kelly, Oct 12, 2015
  10. Chamodh Madusanka

    Chamodh Madusanka New Member

    Joined:
    Oct 3, 2015
    Messages:
    4
    Likes Received:
    0
    My r1plus doesn't have the two allen screws why is that. I watched your tutorial video you say to unscrew the two allen screws but there is no screws. Only the bottom screw

    Sent from my SM-G900FD using Tapatalk
     
    #10 Chamodh Madusanka, Oct 12, 2015
  11. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    #11 mark tomlinson, Oct 12, 2015
    Chamodh Madusanka likes this.

Share This Page