1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

XXL screen availability

Discussion in 'Mods and Upgrades' started by kain0r3D, Jun 16, 2016.

  1. kain0r3D

    kain0r3D New Member

    Joined:
    Mar 30, 2016
    Messages:
    25
    Likes Received:
    2
    I'm chasing a plug and play screen to monitor SD card printing on my Robo3D R1 Plus. Everywhere seems to be sold out (XXL).

    Any idea where I could get one?

    I'm in Australia, so will need the option of international shipping. Has to be plug and play.
     
    #1 kain0r3D, Jun 16, 2016
  2. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    Since I understand that shipping from China to Australia is a lot cheaper than from anywhere else in the world. But it seems no one is making the XXL anymore. But there are plenty of 2004's which is what the XXL was based on and functionally equivalent to.

    Banggood
    AliExpress
     
    #2 WheresWaldo, Jun 17, 2016
    Geof and mark tomlinson like this.
  3. WADZOQUADZ

    WADZOQUADZ Member

    Joined:
    Mar 16, 2015
    Messages:
    90
    Likes Received:
    23
    Personally its not worth spending a lot for a xxl when the full graphics lcd can be had for 10bucks on ebay and its better then the xxl. I have both and got the xxl at printedsolid for like 4x the price. If i were to get one from the start it would be the full graphic
     
    #3 WADZOQUADZ, Jun 19, 2016
    Ryan TeGantvoort and WheresWaldo like this.
  4. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    #4 WheresWaldo, Jun 19, 2016
  5. kain0r3D

    kain0r3D New Member

    Joined:
    Mar 30, 2016
    Messages:
    25
    Likes Received:
    2
    Is that this one? http://goo.gl/1eKOG6

    Is that just plug and play with the current R1+ firmware?
     
    #5 kain0r3D, Jun 28, 2016
  6. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    @kain0r3D Well, it's plug, modify two lines in the firmware, upload the firmware, then play. It makes a world of difference and has been documented many times on this forum.

    Hint: If search does not work for you (everybody actually), you can use Google to search the entire forum with a command like this: firmware modification full graphics controller site:community.robo3d.com

    It is the site: parameter that limits Google to searching a single website.
     
    #6 WheresWaldo, Jun 28, 2016
    Geof and mark tomlinson like this.
  7. kain0r3D

    kain0r3D New Member

    Joined:
    Mar 30, 2016
    Messages:
    25
    Likes Received:
    2

    I just ordered the one on eBay I listed, should be no dramas making the firmware change. Do you know if there would be any problems using an eyefi card in it?
     
    #7 kain0r3D, Jul 4, 2016
  8. WheresWaldo

    WheresWaldo Volunteer ( ͠° ͟ʖ ͡°)
    Staff Member

    Joined:
    Feb 18, 2015
    Messages:
    5,905
    Likes Received:
    3,593
    No experience with EyeFi cards, only know what I have read recently.
     
    #8 WheresWaldo, Jul 4, 2016
  9. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    I have a pair, but never actually used them for anything... yet.
     
    #9 mark tomlinson, Jul 4, 2016

Share This Page