1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 10 of 10
  1. Geof
    Post

    R2 - nozzle crashes on the printbed

    Im sure you have, but have you cleaned the bed. Also please copy and paste your start up scripts here for us to look at
    Post by: Geof, Feb 16, 2019 in forum: Troubleshooting
  2. Geof
    Post

    How fast can we go?

    I finally broke down and have one R1 series running the volcano with a 1.0 nozzle and it makes all my jigs and fixtures. Nice and fast :D ugly if...
    Post by: Geof, Feb 12, 2019 in forum: General Questions
  3. Geof
    Post

    Solved Unprinted section on prints?

    @Avrution the only thing I can think of that would cause an issue at the exact same height is a binding in the rod. Does it move up and down...
    Post by: Geof, Feb 12, 2019 in forum: Troubleshooting
  4. Geof
    Post

    How fast can we go?

    I have quite a few printers - they are all slow :D. Even my Ultimaker. If you have no need for quality put a volcano hotend on it and print huge...
    Post by: Geof, Feb 12, 2019 in forum: General Questions
  5. Geof
    Thread

    A reminder that you dont always know best ;)

    https://e3d-online.com/blog/2019/02/12/appearances-can-be-deceiving/ Huge uproar about photos showing "evidence" of bad Nozzle X parts. E3Ds...
    Thread by: Geof, Feb 12, 2019, 0 replies, in forum: Off Topic
  6. Geof
    Post

    How fast can we go?

    I can promise you makerbot does not run those speeds in reality. Had a 5th gen I was fixing where that was the claim, but at 40mm/s my Robo out...
    Post by: Geof, Feb 12, 2019 in forum: General Questions
  7. Geof
    Post

    Question about IR sensor and glue stick

    standard V2 heatbed with buildtak.
    Post by: Geof, Feb 11, 2019 in forum: General Questions
  8. Geof
    Post

    Question about IR sensor and glue stick

    nope, use glue stick all the time on my R2 for Nylon/PC etc without issues. I do not use glass because it alone can mess with the IR and I do not...
    Post by: Geof, Feb 11, 2019 in forum: General Questions
  9. Geof
    Post

    Solved Unprinted section on prints?

    Hmmm it does seem that sticky thread is no longer a sticky and was so old there’s no way I’ll find it lol. How’s bout a video :) [MEDIA]
    Post by: Geof, Feb 10, 2019 in forum: Troubleshooting
  10. Geof
    Post

    Solved Unprinted section on prints?

    I use brake clean on a rag to take off oil and gunk. Just keep it off everything except the rod, it will not be good on ABS parts. There is a...
    Post by: Geof, Feb 10, 2019 in forum: Troubleshooting
  11. Geof
    Post

    Solved Unprinted section on prints?

    The exact same height makes me think z stepper drivers or a binding on z. Clean and oil the rods and check the driver voltage
    Post by: Geof, Feb 10, 2019 in forum: Troubleshooting
  12. Geof
    Post

    Solved Unprinted section on prints?

    2nded
    Post by: Geof, Feb 10, 2019 in forum: Troubleshooting
Find older messages
Showing results 181 to 192 of 192
Search Again
Page 10 of 10