1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Vandel212
    Post

    Answered Z-Axes out of sync with Simplify 3D

    Just figured I'd follow up on the thread for posterity. I bought the drivers you suggested, said screw it, and just replaced all 5 on the printer....
    Post by: Vandel212, Mar 19, 2019 in forum: Troubleshooting
  2. Vandel212
    Post

    Answered Z-Axes out of sync with Simplify 3D

    Is thermal paste alone enough to keep it on there?
    Post by: Vandel212, Mar 14, 2019 in forum: Troubleshooting
  3. Vandel212
    Post

    Answered Z-Axes out of sync with Simplify 3D

    Ah, I did not know that. Thank you. So odds are it's still a little out of level after a print if I don't use the G29 command, just less than...
    Post by: Vandel212, Mar 6, 2019 in forum: Troubleshooting
  4. Vandel212
    Post

    Answered Z-Axes out of sync with Simplify 3D

    Shouldn't the z-axis remain still until it's time to go to the next layer?
    Post by: Vandel212, Mar 6, 2019 in forum: Troubleshooting
  5. Vandel212
    Post

    Community Favorite Marlin 2.0.x release for Robo R1+

    I have a Robo3D R1+, and upgraded the hotend to the E3D V6. If I upgrade the firmware, is all I need to do in the firmware just what is stated in...
    Post by: Vandel212, Mar 5, 2019 in forum: Mods and Upgrades
  6. Vandel212
    Post

    Answered Z-Axes out of sync with Simplify 3D

    Sorry to resurrect an old thread, but I'm still having this issue, I just took a break from the printer. I got in touch with Simplify3D's support,...
    Post by: Vandel212, Mar 5, 2019 in forum: Troubleshooting
  7. Vandel212
    Post

    Answered Z-Axes out of sync with Simplify 3D

    I double checked, I picked the Robo3D R1 Plus profile. If one slicer works (Craftware) and one doesn't (Simplify 3D), how could it be a firmware...
    Post by: Vandel212, Jan 12, 2019 in forum: Troubleshooting
  8. Vandel212
    Thread

    Answered Z-Axes out of sync with Simplify 3D

    Hi, I have a Robo 3D R1+, and I'm using the default profile for it with simplify 3D. When I finish a print, I notice that my X Gantry is way out...
    Thread by: Vandel212, Jan 11, 2019, 16 replies, in forum: Troubleshooting
  9. Vandel212
    Post

    Partial Answer E3D V6 Hotend Not Getting Hot Enough

    I forgot to mention that the LCD screen does say it's the temp that I set it to. It's just not melting the plastic. Do you still think it's the...
    Post by: Vandel212, Mar 5, 2018 in forum: Troubleshooting
  10. Vandel212
    Thread

    Partial Answer E3D V6 Hotend Not Getting Hot Enough

    Hi, I put the E3D V6 hotend in my printer, and I'm running into an issue where the printer is not getting hot enough. I flashed the firmware with...
    Thread by: Vandel212, Mar 5, 2018, 3 replies, in forum: Troubleshooting
  11. Vandel212
    Thread

    Is There A Firmware Upgrade for R1+

    Hi, Where can I find out if there is a firmware update for the Robo 3D R1+? I purchased it December 30th of 2016 and have never done a firmware...
    Thread by: Vandel212, Jan 24, 2018, 10 replies, in forum: General Questions
Showing results 1 to 11 of 11
Search Again